Sanyo SRT-8960 SETTING FOR RS-485OR RS-232CUSE, Settings when using RS-485, Setting the Address and Data Transfer, Speed, Y, N, JOG, JOG, JOG, JOG, dial, or more, COUNTER

or more.

1 PressCOUNTERthe RESET button for 3 seconds

SETTING FOR RS-485 OR RS-232C USE

The RS-485 interface can be used to operate the VCR	Settings when using RS-485
using a SANYO brand system controller. Furthermore,	1 PressMENUthebutton to display the MAIN MENU.
the RS-232C interface can be used to operate the VCR	1 PressMENUthebutton to display the MAIN MENU.
using a computer.	2 TurnJOGthedial to select the“9.OTHERS” line,
	then turn the SHUTTLE ring clockwise.

NOTES:

ø The (OTHERS) menu appears.

œ This can only be used when the RS-485/232C

interface board (VZU-485/232C) is installed*ALARM@LOG .

*POWER@FAILURE/DEW

œ Refer to the instruction manuals for *TERMINAL@SET@@@@SET1the

*RS-485@SET

VZU-485/232C, the system controller and/or@@STATUS@INFO.@@@Ythe

computer.

@@ALARM@INFO.@@@@Y

	Setting the Address and Data Transfer	3 TurnJOGthedial until the“STATUS INFO.” setting
	Speed	3 TurnJOGthedial until the“STATUS INFO.” setting
	Speed	is highlighted, then turn the SHUTTLE ring clockwise.

œ Make this setting without a4cassetteTurnJOGthedialtapeto set theinserted“STATUS INFO.”. setting, then turn the SHUTTLE ring clockwise.

ø“485” or “232” appears on the digital display.

2TurnJOGthedial to select the interface being used,RS-232C or RS-485.

Y. . . . . . . . . . The VCR status information is output at the RS-485 connector.

N . . . . . . . . . The status information is not output at the RS-485 connector.

ø “232” or “485” appears on the digital display.	5 TurnJOGthedial until the“ALARM INFO.” setting is
ø “232” or “485” appears on the digital display.	highlighted, then turn the SHUTTLE ring clockwise.
	highlighted, then turn the SHUTTLE ring clockwise.
œ When setting“232”, carry out step 3 and then
step6.	6 TurnJOGthedial to set the“ALARM INFO.” setting,
step6.	then turn the SHUTTLE ring clockwise.
3 TurnSHUTTLEthe ring clockwise.	then turn the SHUTTLE ring clockwise.
3 TurnSHUTTLEthe ring clockwise.	Y. . . . . . . . . .	The VCR alarm information (alarm
4 TurnJOGthedial to set the VCR address (from 000	Y. . . . . . . . . .	The VCR alarm information (alarm
4 TurnJOGthedial to set the VCR address (from 000		recording start and stop) and
to 127).		video loss information are output
ø The address set appears on the digital display.		at the RS-485 connector.
5 TurnSHUTTLEthe ring clockwise.	N . . . . . . . . .	The VCR alarm information (alarm
6 TurnJOGthedial to set the data transfer speed		recording start and stop) and
6 TurnJOGthedial to set the data transfer speed		video loss information are not
(19200, 2400, 4800, 9600).		video loss information are not
(19200, 2400, 4800, 9600).		output at the RS-485 connector.
		output at the RS-485 connector.
ø The data transfer speed set appears on the	7 PressMENUtheEXIT button.
digital display.	7 PressMENUtheEXIT button.
digital display.	8 Set TERMINATEthe switch on the back panel to the
7 When finished,COUNTERPressRESET buttonthe.	8 Set TERMINATEthe switch on the back panel to the
	“ON” or “OFF” position

NOTE:

œWhen MENUthe RESET button is pressed, the setting appearing on the digital display is reset to the default setting.

OFF side . . . Not terminated

ON side . . . . Terminated

NOTE:

œWhen a warning state (non-reco problem or clog detection) occ output from the RS-485 connec

non-recording warning states“NON a

REC” is set to “N” in the (WARNING OUT/CONTROL SET) menu. In addition, the clog detection warning state is not output if “CLOG DETECT.” is set to “N” in the (GENERAL SET) menu.

English