Repeat this action to change the Lock Level setting. The Lock Level setting can be changed from any channel. If Lock Level 3 is set and any button is pressed, you are prompted to enter the current Password. After the correct Password is entered, the Lock Level setting is automatically changed to Level 0. If an incorrect Password is entered, “bAd” is displayed at the front panel. For more information about Lock Levels, see “…About Lock Levels”.

 

Frequency

 

/2￿)UHTXHQF\￿￿￿

 

 

he LO (Local Oscilla or)

and

 

#1 option is an Alt-2 Mode function. The LO

 

press SELECT

Frequency #1 sets the satellite ant

 

na LNB local oscillator #1 frequency, and is

valid only if the Frequ ncy Mode is

 

Frequency

t to -Band 1 (Lb1) or Downlink (dnLn). If

y u are un ure about which Local O cillat r Frequency to u e, contact your Todealer/reseller,displayorchangeor localtheerviceLOprovid .#1Ö

 

 

frequency

 

PerformStep321...thesaveWhenfrombuonPressTheIfrequired,ttfirstALTing02ALTGHzdisplays(LOLEDtep9twicepress.through1)750GHziftoONyouhighertodisplay0.chnge15.eorGHzthenchangingthelowerfrom(seecurrentfrequencynormalìÖAbouttheLOLOoprationsettingstodisplayto#1panel,(frequeciesAl.sttigsî)Pressing#1t-heInstaller.2Modethe..areTheœChanneldispldefault/–yedrrow.

Step4.

thesettingdesired.settingisdisplayedatthefront

pressSELECTto

 

Thefrontpaneldisplaysìsav?î.

 

 

Available options: Press 1 to save the new setting (donE), or press 2 to discard all changes (rstr), or press 3 to cancel the operation (abrt).

Repeat this action to change to another frequency. You can use the Õ/Œarrow buttons to change between low and high resolution. When displaying high resolu- tion (i.e., least significant digits), the decimal point flashes ON and OFF repeatedly. The Local Oscillator #1 frequency can be displayed from any channel, but can only be changed from the Installer Channel (see “…About the current channel”). The Local Oscillator #1 frequency is associated with the L-Band 1 [Lb1] Frequency Mode, and must be lower than the Local Oscillator #2 frequency. For more infor- mation about frequency settings, see “Setting up the receiver”.

/2￿)UHTXHQF\￿￿￿

he LO (Local Oscilla or) #2 option is an Alt-2 Mode function. The LO Frequency #2 sets the atellite antenna LNB Local Oscillator #2 frequency, and is

valid only if the Frequ ncy Mode is

t to -Band 2 (Lb2) or Downlink (dnLn). If

y u are un ure about which Local

O cillat Frequency to use, contact your

dealer/reseller,Todisplayorchangeor localtheerviceLOprovid

 

.#1Ö

Frequency

 

PerformStep321...thedefaultplayedrowPressTheIfrequired,firstALTbutt5ALTfrsetingLED(LOsteposettingm0twicepressdisplays2)toifGHzONyouto0display.10through.600igherthenchangingtheGHzfromor15currentlowerGHz.normalthe(sfreLOquencyLOìÖAbouttodisplaysettings(frequenciestofrequency#2Alt.#2theInstallerPressing-.2Modesettingsî).theChannelareœ./–Thedisar-.-

 

 

and

press SELECT

 

 

change

 

operation

Step4.When

 

 

 

Frequency

desiredsettingisdisplayedatthefrontpanel,pressSELECTto

savethe

.

 

 

 

Thefrontpaneldisplaysìsav?î.

 

Available options: Press 1 to save the new setting (donE), or press 2 to discard all￿￿ changes (rstr), or press 3 to cancel the operation (abrt).

Page 31
Image 31
Scientific Atlanta D9225 manual 2UHTXHQF