Scientific Atlanta D9225 manual Ku-Band,andthen

3				C-	s		L.O.Freq#1to		desiredC-Bandfrequency(0
	theAllo8networkGHz).freuencyatpresetstheReceiverdefinedwithdownlinkSetthisstepupmenu,frque.adnciesthenrangingsavethefromseting0 8.GHzwilluse
Step4.IfyouwanttouseKuBand,-						andifyourLNBhastwolocaloscillators
	tingsL.OFreq.	#1,L.O.Freq#2,andCrossoverfor							Ku-Band,andthen		savethe
	IfyouwanttouseKu-					andifyourLNBhasonlyoneloclocillator
	setbothL.O.Freq#1BandL.O.Freq#2tothesamesettingasisapplicableto
	yourLNB.			withdownlinkfrequencies					reaterthan8GHzwillusethe
Step5.	Allnetwork
	GobacktothNetworkPresetpresetssmenutoconfiguretherestofthesettings.
	L.O.frequenci		definedinthis				tep.
TosettheoperatingFrequencyÖ									andCrossoverfrequenciesas
1.	Besureyouhave			onfiguredtheLocal
2.	descibed		.	andpressSELECTOscillatorreplacethecurrentsetting.
	MovetoFrequ
Step3.	EnteravaldabovefrquencyandthenpressSELECT.Youcan									presstheœ/–
	arrowbuttonsto				available			from0GHzthrughalso15GHz
Step4.	(Downlink)in250kHzdisplayeps.Thedefaultsettings							tingforDownlinkis10.7GHz.
	Whenthedsiredsettingisdisplayedon-screen,movetoExitandpress
Step5.	SELECT,orpress1andthenpressSELECTtochangethecurresetting.
	Press1tosavethenewsetting(YES),orfollowtheon-screeninstructions,as
	Apop-upmenudisplaysSaveoptions.
	required.

Available options: Press 1 to save the new settings (Yes), or press 2 to discard all changes (No), or press 3 to cancel the operation (Cancel).

Repeat this action to change to another frequency. A valid operating Frequency is always required (i.e., for setting the Downlink frequency).

StepToset21..theMovedescribedBe(Hantnna[Horizontal],suretoyouhavePolrizationaboveLNB.HconfiguredpolarizationÖ(Fixed),andVpress[Vertical])theLocalSELECTOscillatorV(Fixed)displayand.TheavailableCrossoverdefaultsettingsfrequenciesisas

Step34..WhenSELECT,APress(Horizontl)pop-the1uptomenudsiredsavepress.displaysthe1settingandnewthensettingSaveisdisplayedpressoptions(YES),SELECT.onor-screen,followtochangethemoveonthecurrent-toscreenExitandinstructions,settingpress.as

required.

Available options: Press 1 to save the new settings (Yes), or press 2 to discard all changes (No), or press 3 to cancel the operation (Cancel).

Rep at is action to change the polarization. When a Horizontal polarization is set, a 19 volt DC signal is output via the receiver rear panel SATELLITE connector. When a V rtical polarizati is s t, a 13 volt DC signal is output via this connector. Ob rve the eff ct of the polarization change by checking the displayed relative ignal Str ngth and Signal Q ality values (see Figure 12). Higher numbers are better. If you5/6, re unsure about which polarization to use, contact your

StepTodealsetr/res21..the3/4,MovedescribedBeFECrateÖllsureyoutoorFECor7/8)abovelochaveRatel service..configuredtheLocalTheefaultsettingandpressSELECTprovid r. isOscillator7/8display.andavailableCrossoverfrequenciessettings(1/2,2/3,as 3.WhenSELECT,theormenudsiredsettingpress1andthenisdisplayedpressSELECTon-screen,tochangemovethecurrenttoExitandsettingpress. Step4.APressrequiredpop-1upto.savedisplaysthenewsettingSaveoptions(YES),.orfollowtheon-screeninstructions,as￿￿

Available options: Press 1 to save the new settings (Yes), or press 2 to discard all changes (No), or press 3 to cancel the operation (Cancel).