Step324..SELECT,WhenGHzarrowbuttonsEnterAPresspopthrough-the1auptovalidormenudsiredsavepress1frequency15todisplaystheGHzsettingandthennew1andsettingSaveoptionsMHzavailableisthendisplayedpressSELECTsteps)(YES),ressettings..TheonorSELECT-defaultscreen,movefollowto(frequencieschange.theYousettingonanthecurre-toscreenaloaredisplayedisExit10press.andinstructions,600settingpresstheGHzfromœ./.–0asrequired.

Available options: Press 1 to save the new settings (Yes), or press 2 to discard all changes (No), or press 3 to cancel the operation (Cancel).

Rep at is acti n to change to another frequency. A Local Oscillator #2 frequency se ting is required only if the Downlink or -Band/2 Frequency Mode set (N/A1 displayed if Frequency Mode set to L-Band/1, if op rating F qu ncy in C-Band range [3.7-4.2 GHz]). The Loc Oscillator #2 frequency used must be greater than

theToStepsettheLocal12..MoveEnterarrowbuttons10Oscillator.Crossover7GHztoavalidCrossoverthrough15#1frequencytoandGHzin250andpress.availablethenkHzpresssettSELECTingstoep)replace.(frequnciesThe.Youdmovethefaultancurrentalsosettingarepresssetting11the.700.fromœ/GHz–.

Step3.

 

frequencyÖ

oExitdisplayedandpress

Whenthedsiredsettingdisplay isdisplayedSELECTon-creen,

 

SELECT,orpress1andthenpressSELECTtochangethecurresetting.

Step4.

Apop-upmenudisplaysSaveoptions.

 

Press1tosavethenewsetting(YES),orfollowtheon-screeninstructions,as

 

required.

 

 

Available options: Press 1 to save the new settings (Yes), or press 2 to discard all changes (No), or press 3 to cancel the operation (Cancel).

￿￿Repeat this action to change to another frequency. A Crossover frequency setting is required only if the Downlink Frequency Mode is set (N/A1 displayed if Fre- quency Mode set to L-Band/1 or L-Band/2 [not dual Ku-Band LNB operation]). The Crossover frequency setting determines which LNB is used (only for dual-LNB operation).

StepToset12..the(HMoveWhenthe(Horizontal)antenna[Horizontal],toPolrizationmenudsiredLNB.HplarizationÖsettingis(Fixed),andVpress[Vertical])displayedSELECTonorV-toscreen,(Fixed)displaymove.TheavailabletodefaultExitsettingsandpressis

Step3.SELECT,ApopPress-1uptosavepressdisplaysthe1andnewthensettingSavepressoptions(YES),SELECTto.orfollowchangetheonthecurrent-screeninstructions,setting.as

required.

Available options: Press 1 to save the new settings (Yes), or press 2 to discard all changes (No), or press 3 to cancel the operation (Cancel).

Rep at is action to change the polarization. When a Horizontal polarization is set, a 19 volt DC signal is output via the receiver rear panel SATELLITE connector.

When a V rtical polariza ion is set, a 13 volt DC signal is output via this connector. Ob rve the effect of the polarization change by checking the displayed relative

ignal Str ngth and Signal Quality valu

(see Figure 12). Higher numbers are

better. If you re unsure about which

polarization

use, contact your

settingto

StepTodealStepsetr/resell213...theASELECT,When3/4,MovePresspopFECrateÖ5/6,r,-totheup1ortoFECormenuor7/8)dsiredsettinglocalsavepress1Ratedisplaysthe.erviceTheefaultandandnewthenpressSELECTtosettingprovidSaveisdisplayedonpressoptions(YES),.SELECT.isor7/8-displayscreen,followto.changetheavailablemoveonthecurrent-screenExitsettingsandinstructions,settingpress(1/2,2/3,.asrequired.

Available options: Press 1 to save the new settings (Yes), or press 2 to discard all changes (No), or press 3 to cancel the operation (Cancel).

Repeat this action to change the FEC Rate. The selected FEC Rate must match the FEC Rate associated with the transmitted signal. If you are unsure about which FEC rate to use, contact your dealer/reseller, or local service provider.

Page 38
Image 38
Scientific Atlanta D9225 manual Required