general safety instructions for power tools

1. KNOW YOUR POWER TOOL

Read the owner's manual carefully. Learn its
application and limitations as well as the specific
potential hazards peculiar to this tool.

2. GROUND ALL TOOLS

This tool is equipped with an approved 3-conductor
cord and a 3-prong grounding type plug to fit the
proper groundingtype receptacle. The greenconductor
in the cord is the grounding wire. Never connect the
green wire to a live terminal.
3. KEEP GUARDS IN PLACE
and in working order.
4. REMOVE ADJUSTING KEYS
AND WRENCHES
Form habit of checking to see that keys and adjusting
wrenches are removed from tool before turning it on.
5. KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents. Floor
must not be slippery due to wax or sawdust.
6. AVOID DANGEROUS ENVIRONMENT
Don't use power tools in damp or wet locations. Keep
work area well lit. Provide adequate surrounding work
space.
7, KEEP CHILDREN AWAY
All visitors should be kept a safe distance from work
area.
8. MAKE WORKSHOP KID-PROOF
- with padlocks, master switches, or by removing
starter keys.
9. DON'T FORCE TOOL
It will do the job better and safer at the rate for which
it was designed.
10. USE RIGHT TOOL
Don't force tool or attachment to do a job it was not
designed for.

11. WEAR PROPER APPAREL

No loose clothing, gloves, neckties or jewelry to get
caught in moving parts. Rubber-soled footwear is
recommended for best footing.

12. USE SAFETY GOGGLES

Safety gogglesmust comply with ANS Z87.1-1968.
Also useface or dust maskif cutting operation is dusty.

13. SECURE WORK

Use clamps or a vise to hold work when practical. It's
safer than using your hand, frees both handsto operate
tool.
14. DON'T OVERREACH
Keep proper footing and balance at all times.
15. MAINTAIN TOOLS WITH CARE
Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and
changingaccessories.
16. DISCONNECT TOOLS
before servicing; when changing accessories such as
blades, bits, cutters, etc.
17. AVOID ACCIDENTAL STARTING
Make sure switch is in "OFF" position before plugging
in.

18. USE RECOMMENDED ACCESSORIES

Consult the owner's manual for recommended
accessories. Follow the instructions that accompany
the accessories.The use of improper accessoriesmay
causehazards.

19. NEVER STAND ON TOOL

Serious injury could occur if the tool istipped or if the
cutting tool is accidentally contacted.
Do not store materials above or near the tool such that
it is necessary to stand on the tool to reach them.
20. CHECK DAMAGED PARTS
A guard or other part that is damaged should be
properly repaired or replaced before further use of the
tool.
Carefully check the repaired or new part to assure that
it will operate properly and perform its intended
function.
If power cord is worn or cut, or damaged in any way,
have it replaced immediately.
The operation of any power tool can result in foreign objects being
thrown into the eyes, which can result in severe eve damage. Always
wear safety goggles complying with ANS Z87.1-1968 before
commencing power tool operation. We recommend Wide Vision
Safety Mask for use over spectacles, or standard safety goggles ...
available at Sears retail or catalog stores.
THIS SAFETY SEAL OF THE
POWER TOOL INSTITUTE ASSURES YOU...
1. That the manufacturer's power tools, including the particular tool
assoc;ated w;th the Seal, are produced in accordance with applicable
,Standards For Safety of Underwriters' Laboratories and American
National Standards (ANSI).
2. That compliance with applicable safety standards is assured by in-
dependent inspection and testing conducted by Underwriters' Labora-
tories (UL).
3. That every motorized tool is inspected under power.
4. That every tool has with it adequate instructions and a llst of safety
rules for the protection of the user.
5. That the tool manufacturer isa member of the Power Tool Institute and
is a sponsor of the Institute's Consumer Safety Education Program.
2 Copyright 1969 by Powe rTool Institute, Inc. AI_ r_ghts reserved.