SELECTING A SPECIAL MODE

The procedure for selecting settings for "Adding margins (Margin Shift)" is explained below as an example. Although the specific settings for each special mode vary, the general procedure is the same.

The side to be scanned must be face up!

1 Place the originals.

When using the document glass, place the original with the side to be scanned face down.

Ready to scan for copy.

02 Select settings in the touch panel.

Job Detail

Settings

Original

 

A4

 

2-Sided Copy

 

 

Output

Plain

(1) Touch the [Special Modes] key.

Auto

Exposure

A4

1.A4

Special Modes

100%

Copy Ratio

Special Modes

Margin Shift

(2)

Pamphlet Copy

 

 

 

 

A4R

 

 

 

(1)

 

 

2.

 

 

 

 

 

 

File

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3.

 

B4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4.

 

A3

 

 

 

 

Quick File

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1/4

 

 

Erase

 

 

 

Dual Page

 

 

 

 

 

 

 

 

 

 

 

 

 

Copy

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Job

 

 

Tandem

 

 

Build

 

 

Copy

 

(2)Touch the [Margin Shift] key.

Shifting the left margin by 15 mm will be explained as an example.

(3) Select 15 mm for the front side and

15 mm for the reverse side using

Special Modes

OK

the

keys.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(4)

 

 

The margin shift position is initially set to

 

 

 

 

 

 

 

 

 

 

 

 

 

Cancel

 

 

 

 

Margin Shift

 

 

 

 

 

 

 

 

 

 

 

 

 

OK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

"Right".

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Side 1

 

 

 

 

Side 2

 

 

Right

 

 

Left

Down

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To change the position to "Left" or "Down",

 

 

 

 

 

 

15

 

mm(0~20)

 

 

 

 

 

15

 

mm(0~20)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

touch the corresponding key.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(3)

 

 

 

 

 

 

 

 

 

(4) Touch the [OK] key.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3 Set the number of copies and then press the [START] key.

Correct sets Cancel scanning Cancel copying

34

Page 36
Image 36
Sharp MX-M503U, MX-M453U, MX-M363U Selecting a Special Mode, Touch the Special Modes key, Touch the Margin Shift key, Keys