When selecting the Dolby Virtual Speaker | Sherwood R-871 specs

When selecting the DOLBY VIRTUAL SPEAKER

•You can select the speaker layout to be used actually for each Dolby Virtual Speaker mode.

■Note:

•The speaker layout settings are valid only when listening in a Dolby Virtual Speaker mode.

Press the CURSOR UP(▲)/DOWN(▼) buttons to select the DOLBY VIRTUAL SPEAKER,

1 then press the ENTER button.

Press the CURSOR UP(▲)/DOWN(▼) buttons to select the desired Dolby Virtual Speaker mode.

2

Press the CURSOR LEFT(◀)/RIGHT(▶) buttons to select the desired speaker layout.

3

■When selecting the Dolby Virtual Speaker Reference mode

2 SPK : When using 2 front speakers only.

3 SPK : When using 2 front and center speakers.

■When selecting the Dolby Virtual Speaker Wide mode

2 SPK : When using 2 front speakers only.

3 SPK : When using 2 front and center speakers.

4 SPK : When using 2 front and 2 surround speakers.

5 SPK : When using 2 front, center and 2 surround speakers.

■Note:

• When the speakers are set to "NONE", the corresponding speaker layouts cannot be selected.

4	Repeat the above steps ② and ③ to select the desired speaker layout for another Dolby
	Virtual Speaker mode.

ENGLISH

67

Image 68

Sherwood R-871 manual When selecting the Dolby Virtual Speaker Wide mode

Contents

Page Page Safety Instructions Introduction Read this Before Operating Your Unit Contents Connecting Antennas System Connections Connecting Video Components Hdmi High Definition Multimedia Interface connection *1 Connecting Audio Components Component Video Composite Video Digital input default settings Connecting External INSConnecting Digital INS and OUT Connecting DC Trigger OUT Connecting PRE OutsConnecting System Control Surround back speakers Connecting SpeakersFront speakers a and B Speaker placement Front left and right speakers and center speakerSurround left and right speakers Surround back left and right speakers Connecting Room 2 Outs Connecting PC for Upgrades Connecting MULTI-ROOM System KIT Connecting XM DT only for North America Switched AC Outlets AC Input Front Panel Controls Fluorescent Display Setup MIC Jack Universal Remote Controls Digi Link system remote controls Function Table of the Numbered Buttons Loading Batteries Using Functions of Remote Control Entering a setup code Searching a setup code Programing the commands from other Remote controls Learning mode Erasing the programmed command Erasing all the commandsProgrammed under a device mode From one button Programming a macro function Operating a macro functionTo erase a macro program To change a macro program Programming a punch-through function → TV Delete SAT Cable VCR ← Operating a punch-through function Erasing the programmed puch-through function English Loading Battery Room 2 Remote ControlsRemote Control Operation Range When selecting the External in as desired OperationsListening to a Program Source Before operation When CD, AUX, Video 1~ 5 is selected as an input source Muting the sound Listening with headphones Achieving higher purity of sound quality Surround modes Dolby Pro Logic IIx surround Dolby Pro Logic II surroundDolby Virtual Speaker Dolby Headphone Enjoying Surround Sound Dolby DIGITAL, Dolby VS REFERENCE, Dolby VS Wide Listening in a Dolby Headphone mode Adjusting each channel level with test toneTo cancel the surround mode for stereo operation 2CH downmix mode Adjusting the current channel level Memorizing the adjusted channel levels Recalling the memorized channel levels Auto tuning Manual tuningAuto presetting Listening to Radio Broadcasts Manual presetting Memory Backup Function XM Satellite Radio only for North America Listening to XM Satellite RadioSigning up for XM Satellite Radio Whats XM Satellite Radio? Category search Channel searchDirect search Displaying XM information Presetting channelsPreset search Dubbing the audio and video signals RecordingRecording with Tape Dubbing from video components onto Digital Audio Recording with MD Recorder Operating the sleep timer Adjusting the brightness of the fluorescent displaysOther Functions Displaying the audio information Room 2 Source Playback Input ~ OSD Menu Settings Confirm your selection When selecting the AMP Assign Setting the System SetupWhen selecting the items other than OSD Position Adjust When selecting the Subwoofer Mode When selecting the Tone Control When selecting the Cinema EQ When selecting the BackgroundWhen selecting the Momentary OSD When selecting the OSD Position Adjust Setting the Input Setup When selecting the items other than NameWhen selecting the Digital Audio When selecting the Video Assign When selecting the Video Mode When selecting the Auto SurroundWhen selecting the Remaster When selecting the AV Sync When selecting the DC Trigger When selecting the Name Setting the Speaker / Room EQ Setup When selecting the Auto SetupAbout the first listening position Preparations English When selecting the Speaker Configuration When setting the speaker size by performing the auto setup About the speaker size When selecting the Speaker Distance About the speaker distance When selecting the Speaker Crossover About the crossover frequency When selecting the Room EQ Setting the CH Level Setup Recalling the memorized channel levels Setting the Sound Parameter When selecting the Night Mode When selecting the Dimension control When selecting the Dolby Plii MusicWhen selecting the Panorama mode When selecting the Dolby Headphone When selecting the Dolby Virtual Speaker When selecting the Dolby Virtual Speaker Wide mode Setting the Room 2 Setup When selecting the RoomWhen selecting the Input When selecting the Volume Troubleshooting Guide Problem Possible Cause Remedy Specifications Amplifier Section Setup Code Table AOC VCR STS DVD AUX-TAPE/MD AUX-HOME Automation