8 Touch [OTHER DEVICE]. | To set the [IR SETUP] code |
|
| |||||||||||||||||
When you connect with an A/V connecting | ||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| cable, you need to check the [IR SETUP] code | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| signal to see if your VCR can be operated by | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| your camcorder (infrared ray emitter). | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Remote sensor |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Infrared ray emitter |
| VCR | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
9 Touch [EDIT SET].
10Touch [CONTROL].
11Select [i.LINK] or [IR].
When connecting with an i.LINK cable
Touch [i.LINK], then . Go on to “Step 2 : Adjusting the synchronization of the VCR” (p. 93).
When connecting with an A/V connecting cable
Touch [IR], then . Follow the procedure described in “To set the [IR SETUP] code” (p. 92).
1Touch , then [IR SETUP].
2Select the [IR SETUP] code of your VCR
with / , then touch .
For the [IR SETUP] code of your VCR, refer to “[IR SETUP] code list” (p. 93). When there is more than one code listed for the manufacturer of your VCR, try each code and find the most appropriate one.
3Touch [PAUSEMODE].
4Select the mode to cancel the recording
pause on your VCR, then touch . Refer to the operating instructions supplied with your VCR for details on operation.
5Point the infrared ray emitter of your camcorder towards the remote sensor on your VCR, from about 30 cm (12 in.) away, with no obstructions.
6Insert a cassette into your VCR, and set the VCR to recording pause.
7Touch [IR TEST].
8Touch [EXEC].
The recording starts on your VCR when the setting is correct. [Completed.] appears when the [IR SETUP] code test is finished. Go on to “Step 2 : Adjusting the synchronization of the VCR” (p. 93). When recording fails to start, select another [IR SETUP] code and try again.
92Dubbing/Editing