Connections for a Cut Editing System

The following figure shows a cut editing system

When using a VCR other than the DSR-1800/1800P, refer

configuration that includes two DSR-1800/1800P units to

to its instruction manual.

 

 

 

 

 

 

 

 

 

 

 

 

serve as the player and recorder.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When you select assemble or insert editing mode on

A 75 Ω coaxial cable (not supplied)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the editing control unit, the two DSR-1800/1800P

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

units (recorder and player) will automatically enter the

B 9-pin remote control cable

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

selected editing mode.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(not supplied)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C Cable with RCA phono plugs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

(not supplied)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DSR-1800/1800P

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DSR-1800/1800P

(player)

SDTI(QSDI)OUT

SDTI(QSDI)IN

 

 

 

 

 

 

(recorder)

REF.

VIDEO

OUT

VIDEO

AUDIO

REMOTE

 

OUT 2

MONITOR

 

(SUPER)

OUT

 

 

1

3

2

1

Composite

Audio input

 

 

video input

 

 

 

 

 

REF.

 

 

PLAYER

VIDEO IN

Source monitor

Editing control unit (RM-450/ 450CE, PVE-500, etc.) a)

VIDEO

AUDIO

REMOTE

OUT 2

MONITOR

(SUPER)

OUT

 

1

3

2

Composite

Audio input

 

video input

 

Main monitor

RECORDER

a)For the settings on the editing control unit, see “Settings on an editing control unit” on page 85.

Connections 5 Chapter

Settings on the DSR-1800/1800Ps (recorder and player)

Button

Recorder

Player

 

 

 

REMOTE

On (lit)

On (lit)

 

 

 

9PIN

On (lit)

On (lit)

 

 

 

For details of the video/audio input and audio mode settings for the recorder, see “Settings for Recording” on page 25.

About reference video signals

In order to provide stable video and audio signals for analog editing, it is necessary for the built-in time base corrector (TBC) to operate correctly. To ensure this, input a reference video signal synchronized with the video signal to the REF. VIDEO IN connector.

Settings and

Connections for a Cut Editing System

79