Advanced menu page 2

 

￿

 

 

 

 

 

 

PAGE2 (NEXTm$ PREVm4)￿

 

 

￿

 

 

 

 

 

 

GAIN￿

 

 

 

 

 

 

m HIGH: 18dB

￿

 

 

MID

:

9dB

￿

 

 

LOW

:

OdB￿

 

 

 

￿

 

 

 

 

 

 

DL

: ON ￿

 

 

 

￿

 

 

 

 

 

 

￿

 

 

 

 

 

 

EXIT MENU (YESmPUSH)

 

 

 

 

 

 

 

 

Item

 

 

Settings

 

 

 

 

 

 

 

 

GAIN

This sets gain values for the positions of the GAIN switch. The HIGH, MID, and LOW values must be set so that LOW < MID < HIGH.

HIGH

3 dB, 6 dB, 9 dB, 12 dB, 18

Sets the H position.

dB (normal value), 18 dB +

 

DPR, 24 dB, 24 dB + DPR,

 

HYPER GAIN

 

 

MID

0 dB, 3 dB, 6 dB, 9 dB

Sets the M position.

(normal value), 12 dB, 18

 

dB, 18 dB + DPR, 24 dB, 24

 

dB + DPR

 

 

LOW

–3 dB, 0 dB (normal

Sets the L position.

value), 3 dB, 6 dB, 9 dB, 12

 

dB, 18 dB, 18 dB + DPR, 24

 

dB

 

 

DL

ON (normal value), OFF

Sets DynaLatitude function

When set to ON, the amount

ON/OFF. This setting is

of DynaLatitude effects is

valid only when the

set in basic menu page 2

OUTPUT/DL/DCC+ switch

(see page 79).

has been set to DL.

 

 

 

Advanced menu page 3

￿

PAGE3 (NEXTm$ PREVm4)￿

￿

mAWB MEM

:

2￿

 

PRE. WHT

:

3200￿

 

TONE

:

ON

￿

BARS

:

SMPTEa) ￿

REMOTE1

:

REC￿

 

REMOTE2

:

MARK￿

 

BAUD RATE:

38400

￿

￿

EXIT MENU (YESmPUSH)

a)For DSR-300P: EBU75

Item

Settings

 

 

 

 

 

 

AWB MEM

2 (normal value): No

 

 

Selects whether or not to

correspondence with FILTER

 

 

make the FILTER knob

knob settings. Only two

 

 

settings (1 to 4) correspond

adjustment values (A and B)

 

 

to separate white balance

are stored in memory.

 

 

adjustment values stored in

2 × 4FL: Correspondence

 

 

memory.

with FILTER knob settings.

 

 

 

Each of the four knob

 

 

 

settings can be used to set A

 

 

 

and B adjustment values, for

 

 

 

a total of eight settings.

 

 

 

 

 

 

 

 

 

 

PRE. WHT

3200 (normal value):

 

 

 

 

 

Selects the color

3200 K

 

 

 

 

temperature preset for the

3000: 3000 K

 

 

 

 

 

white balance adjustment.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TONE

ON (normal value): Output

 

 

Chapter

Selects whether or not to

audio signal.

 

 

 

output a 1-kHz audio signal

OFF: Do not output audio

 

 

with the color bars when the

signal.

 

4

OUTPUT/DL/DCC+ has

 

 

 

 

Viewfinder

been set to BARS.

 

 

 

 

 

 

 

 

 

BARS

SMPTE (normal value for

 

 

Selects normal width or

DSR-300):Normal width

 

Screen

narrower width for color

EBU75 (normal value for

 

 

 

bars.

DSR-300P): EBU 75%

 

 

 

EBU100 (for DSR-300P):

 

Indications

 

for normal operation

 

 

EBU 100%

 

 

 

SPLIT (for DSR-300P): Not

 

 

 

SNG: Narrower than normal

 

and

 

(used for satellite

 

 

 

Menus

 

communications, etc.)

 

 

 

 

 

 

 

 

REMOTE1

REC (normal value):

 

 

Sets a function for position 1

Specifies recording start/stop

 

 

of the RM-LG1 connected to

MARK: Specifies a Mark IN/

 

 

the REMOTE connector 1.

OUT point.

 

 

 

CUE: Specifies a Cue point.

 

 

 

NG: Specifies NG/OK.

 

 

 

 

 

 

REMOTE2

REC: Specifies recording

 

 

Sets a function for position 2

start/stop.

 

 

of the RM-LG1 connected to

MARK (normal value):

 

 

the REMOTE connector 1.

Specifies a Mark IN/OUT

 

 

 

point.

 

 

 

CUE: Specifies a Cue point

 

 

 

NG: Specifies NG/OK.

 

 

 

 

 

 

BAUD RATE

9600, 38400 (normal value)

 

 

Sets a baud rate for a

 

 

 

computer connected to the

 

 

 

REMOTE connector 1 (to be

 

 

 

supported in future version).

 

 

 

 

 

 

 

Chapter 4 Viewfinder Screen Indications and Menus 85