Editing 6 Chapter

6-1 Basic Automatic Editing

6-1-5 Confirming Edit PointsDisplaying the duration between two edit points

The following six kinds of duration can be displayed in the time data display window:

•Between IN and OUT points

•Between IN and AUDIO OUT points

•Between IN and AUDIO IN points

•Between OUT and AUDIO OUT points

•Between OUT and AUDIO IN points

•Between AUDIO IN and AUDIO OUT points

Durations are calculated as follows.

•If both IN and OUT points are set, the duration is the time between the points.

•If one of the edit points is not set, the duration is set to 00:00:00.

1 Press the RECORDER or PLAYER button to select the VTR for which you want to confirm a duration.

The button lights up.

2 Hold down any two IN, OUT, AUDIO IN, or AUDIO OUT buttons.

The duration between the points corresponding to the two buttons is displayed. The value can be negative.

 

T I M E R

 

 

 

 

 

 

CH.COND

 

 

 

 

TC

 

 

 

 

S E L

 

 

 

 

 

 

G R E E N

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T C

 

 

 

 

 

 

 

P L A Y

L O C K

 

 

 

 

 

 

 

 

 

T I M E R

D U R

V I T C

 

 

2 F D F 1

 

 

 

 

R E S E T

00Ó 01µ 00ß 00ƒ

 

 

 

 

 

 

Duration

 

 

 

Å I N 0 0 : 0 1 : 1 0 : 0 0 Å O U T 0 0 : 0 2 : 1 0 : 0 0

 

 

 

 

 

 

 

 

 

 

T I M E R

 

between two

 

I N

0 0 : 0 1 : 2 0 : 0 0 O U T

0 0 : 0 2 : 2 0 : 0 0

 

 

S E T

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

edit points

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T I M E R

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

H O L D

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

o f f

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

T C

T C G

 

 

 

 

T C G

 

R U N

D F / N D F

 

V I T C

 

 

 

S E L

S O U R C E

M O D E

 

 

M O D E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

V I T C

 

i n t

 

 

 

p r s t

 

 

 

r e c

 

 

 

d f

 

 

T C G

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Displaying the duration between two edit points

6-1-6 Cuing Up and Prerolling

You can preroll the tape to a point prior to the edit start point (preroll point), or cue up the tape to any edit point.

Follow the procedure below to cue up or preroll the tape.

1

2

Cuing up and prerolling

1 Press the RECORDER or PLAYER button to select the VTR which you want to operate. The button lights up.

2 To cue up the tape to an edit point

Press the IN, OUT, AUDIO IN, or AUDIO OUT button while holding down the PREROLL button. The tape moves to the edit point corresponding to the button, then stops.

To preroll the tape

Press the PREROLL button.

The tape is rewound to a point before the edit start point by the amount determined by the preroll time setting.

Note

When the [F1] (TIMER SEL) button in the TC menu is set to CTL, cuing up is slightly slower than in TC mode. This is to maintain the accuracy of the CTL signals.

You can set up the VTR so that priority is placed on cuing accuracy or speed. Change the VTR setting through 403. CUEUP BY TC and 404. CUEUP BY CTL in the VTR SETUP menu.

6-8Chapter 6 Editing