Manuals / Brands / Computer Equipment / Switch / Sony / Computer Equipment / Switch

Sony MKS-2010, MKS-2015, MKS-2017 [M/E] button:, Saving Snapshots, [PP/ALL] button:

1 200

Download 200 pages, 3.88 Mb

Saving Snapshots

3 2

	7	8	9
M/E	EFF/
M/E	WIPE
	WIPE
	4	5	6
PP/	SNAP
ALL	SHOT
	1	2	3
STORE	MCRO
		EFF	AUTO

5 Press a memory recall button to select a bank.

The most significant digit in the numeric display shows the number of the selected bank.

This is also indicated by the display on the memory recall buttons. For example, the display is as shown below when bank 3 is selected.

37 38 39

34 35 36

31 32 33

BANK TRANS

0

DISS TRNS

40

EFF AUTO

		SEL		RATE

7

4

5,8

6

1 Set up the state that you want to save as a snapshot. 2 Press the [SNAPSHOT] button, turning it on.

The Flexi Pad control block enters snapshot operation mode.

3 Press and light the region selection button for the region which you want to save.

[M/E] button: Selects the M/E region.

[PP/ALL] button: Selects all regions.

4 Press the [BANK SEL] button, turning it on.

The display on the memory recall buttons changes to the state shown in the above figure. You can now select the save destination bank.

Banks are the 99 registers divided into 10 groups. The following table shows the correspondences bank numbers and register numbers.

Bank number	Register number

Bank 0	1 to 10

Bank 1	11 to 20

Bank 2	21 to 30

Bank 3	31 to 40

Bank 4	41 to 50

Bank 5	51 to 60

Bank 6	61 to 70

Bank 7	71 to 80

Bank 8	81 to 90

Bank 9	91 to 99

DISS TRNS

6 Press the [STORE] button, turning it on.

The snapshot can now be saved.

7 Press the memory recall button corresponding to register in which you want to save the snapshot.

Note

The contents of the corresponding register are overwritten if you press a button which is lit in orange or yellow.

The pressed button lights in yellow when the saving of the snapshot is finished.

The numeric display shows the selected bank number, followed by the register number.

For example, if you selected register 37, the display shows “3-37.”

Operations Advanced 6 Chapter

Snapshots 125

Contents

Page Page Introduction System Features Options Control Panel Types Control Panel Configuration Composing Video With Keys Fading the Video to Black Advanced Effect Operations Advanced Key Operations Color Correction Control From Editing Systems Controlling External Devices Simple Connection to MKS-8080/8082AUX Bus Remote Panel Basic Settings Page Overview Chapter Multi-formatsupport State of the art special effects Comprehensive keying capabilities Optimal for use in live broadcast environment Outstanding ease of use Selection of optimal control panel Names and Functions of Parts Principal differences Operation button positions 1.5 M/E panel and 1.5 M/E wide panel 1 M/E panel aCross-pointbutton rows Cross-pointbutton numbers bXPT (cross-point)HOLD button cSHIFT button Tally indicators PGM/PST Cross-PointControl Block Tally indicator AUX Bus Control Block aAUX delegation buttons AUX1 to 4: EDIT PVW: UTIL: eSHIFT button fCross-pointbutton row M/E Transition Control Block aTransition execution section Fader lever: Transition indicator: Transition rate display section: AUTO TRANS (transition) button: bTransition type selection buttons WIPE: PST (preset) COLOR MIX: M/E Key Transition Control Block aKEY1 ON and KEY2 ON buttons DSK PVW (downstream key preview) button DSK independent transition execution section DSK1 ON, DSK2 ON buttons: AUTO TRANS buttons: Flexi Pad Control Block In effect snaphot mode: bRegion selection buttons M/E button: PP/ALL (PGM/PST/all) button (on 1.5 M/E panel): ALL button (on 1 M/E panel): cSTORE button Delegation selection buttons M/E 1CH (M/E1 channel), M/E 2CH (M/E2 channel) buttons: MENU button: bJoystick X-axis BORD (border): SOFT (soft edges): CROP button: N/R (normal/reverse): REV: Macro Control Block Menu Control Block aPRE MCRO button bPOST MCRO button cATTCH ENBL (attachment enable) button b“Memory Stick” status indicator “Memory Stick” slot dUSB connector Usable “Memory Sticks” Handling “Memory Sticks” Using Menus Chapter Accessing Menus by Double Clicking Page Accessing Menus by Single Clicking Basic Screen aMenu page number button bBack button cFwd (forward) button dMenu switch buttons Main Menu button: Detail Menu button: Interpreting buttons General popup windows General popup windows (scrolling type) Numeric keypad window/timecode window aInput value display About timecode input Timecode input examples bMinimum to maximum display Hexadecimal keypad window Keyboard window aItem display bInput string display cLeft button dRight button fCaps Lock button Page number input window Selecting by navigating the menu tree Selecting menus by entering page numbers Selecting menus from the display history Example 1: Example 2: To cancel the exit To restart the menu system Basics of Video Switching Chapter Preparations for operation Page About auto transitions About cut transitions Page Page Basic Operations Chapter Selecting Video in the M/E Cross-PointControl Block When using the 1.5 M/E panel or 1.5 M/E wide panel Selecting Video in the PGM/PST Cross-PointControl Block Selecting Video in the AUX Bus Control Block To select the background of a 2-channeleffect Page To select the transition type To select the next transition Page Selecting Effects With the Flexi Pad Control Block To re-enterthe pattern number When an invalid pattern number is entered Selecting Effects From Menus To scroll the popup window Effect Types About effect pattern numbers Transition effects and non-transitioneffects Transition effects To select channels with the Effect/Wipe control block To select channels from menus Setting the parameters of 2-channeleffects Parameters common to both channels Page Changing Pattern Position and Size With the Joystick To return the pattern size and position to their default Changing Pattern Size and Position From Menus Page Page To set border colors Softening Video Edges (Soft Edge/Soft Border) No borders: Borders: Setting Transition Rates To set transition rates with the Flexi Pad control block To set transition rates from menus Selecting Effect Directions To select effect directions with the Effect/Wipe control block To select effect directions from menus Executing Transitions To switch the video instantly ([CUT] button) To execute a transition at a specified transition rate ([AUTO TRANS] button) To execute a transition with the fader lever About fader lever non-sync Page Luminance key/linear key: Chroma key: Pattern key: To select luminance or linear key and set the key parameters To select a key source To select a key fill To insert and delete keys To select chroma key To select a chroma key source To select a chroma key fill To adjust auto chroma key To adjust chroma key video To select pattern key and set the key parameters About the pattern key source To select the key fill for a pattern key To transform the pattern used in a pattern key When Drop Border or Shadow was selected: To add color to the key edges Masking Part of a Key To check whether a key is over or under To move a key over or under from menus To move keys over and under in a transition To insert or delete a key by mixing (independent key transition) To insert or delete keys instantly To insert or delete M/E keys instantly Using a Color Background To set color To compose a pattern of two colors (color mix) To transform color mix patterns To change the aspect ratio of a pattern To rotate an effect pattern To rotate an effect pattern at a specified speed To modulate an effect pattern To exchange color 1 and color Page To fade out the video with fade to black Advanced Operations Chapter To change the aspect ratio of an effect pattern (Aspect) To rotate an effect pattern (Rotation) To modulate effect patterns (H/V Modulation) To arrange several examples of the same effect pattern (Multi) To mix in a diamond dust effect (Dust Mix) To turn the crop function on To crop to 4:3 in 16:9 mode To set a relationship between transition progress and cropping Light mode and color mode To add beveled edges to video To soften beveled edges Lighting types To add lighting To set the light color To add afterimages To select the image to use in afterimages To transform afterimages into stardust To add shadows To set the shadow color To soften the edges of the shadow Example of a pattern specific transformation (Matrix) Saving effect snapshots Recalling effect snapshots Deleting effect snapshots To turn key clean mode on To invert key signals To adjust the key position To turn the fine key function on Applying 2-colorborders To set separate border widths (Separate Edge function) To select the chroma key composition method To turn the plane function on To adjust chroma keys manually To make adjustments with key active To make adjustments with color cancel To adjust the window To adjust chroma key shadows To adjust the Y balance To adjust video signals Transforming the Pattern of a Pattern Key Position: Aspect: Rotation: To transform a mask pattern To output show key signals Key memory operating modes To recall settings stored in key memory To select a signal To access the CCR menu To enable a color corrector To return all color corrector settings to the defaults To copy or swap color corrector settings To execute input video processing To execute primary color correction To mask part of the primary color correction To execute secondary color correction To mask part of the secondary color correction To execute RGB clip To execute luminance processing To mask part of the luminance processing To execute spot color adjustment To mask part of the spot color adjustment To adjust colors outside the spot color adjustment region To execute output video processing To execute YUV clip Frame memory capacity Hardware and software requirements for using frame memory Assigning frame memory output to crosspoint buttons File names Saving files with [Pair] on/off To apply a box-shapedmask to a freeze image To select frame memory output FM1 V/K: Renaming an image file Deleting an image file Snapshot types Snapshot attributes Saving Snapshots [M/E] button: [PP/ALL] button: Recalling Snapshots Lit in green: Selected Lit in orange: Not selected To maintain cross-pointstates temporarily with the bus override function Deleting Snapshots Macro registers Events Lit orange: Lit yellow: Switching auto insert mode on or off Creating a pause event Executing a macro in normal execution mode Executing a macro with pause zero events set Executing a macro in step execution mode Specifying an edit point Inserting an event Modifying an event Deleting an event Deleting all events within a macro register Setting a macro attachment Removing macro attachment settings Executing a macro by macro attachment Displaying safe title markers with a menu operation Displaying safe title markers with a button operation Copy Operation Targets Using Buttons to Copy Key Settings Example: Copying M/E key 1 to M/E key Page File Operations Chapter To cancel a save after it has started Loading All Data at Once To cancel a load after it has started Deleting All Data at Once To cancel the data deletion after it has started Saving the Data of Selected Categories Loading the Data of Selected Categories Deleting the Data of Selected Categories Loading Data Files Saving Data Files Deleting Data Files To cancel a file deletion after it has started Renaming Data Files Copying Data Files To cancel a file copy after it has started Common Operations – Selecting the Frame Memory Category and the Target Media Preparations on the MFS-2000side Preparations on the editing system side Selecting devices to control Playing VTRs/disk recorders/Extended VTRs Stopping VTRs/disk recorders/Extended VTRs Conducting jog and shuttle mode search Setting start points Checking Device Status Setting variable speeds Loading file lists Loading files Creating new files (disk recorders only) C: SET SWITCHER ID (for AUX mode) D: SET AUX DESTINATION/SOURCE (for AUX mode) R:SET ROUTE Y:SET DISPLAY MODES Z:SET PANEL STATUS Page System Settings Chapter Setting the signal format Setting the input reference signal Setting the screen aspect ratio Selecting resume mode for starting up after powering on Selecting custom mode mode for starting up after powering on Switching M/E PVW or PST output to DSK PVW output Button numbers of cross-pointbuttons Page Signals assigned to cross-pointbuttons Assigning signals to cross-pointbuttons Creating a pair from a video signal and key signal Saving the setup state Saving the initial status Displaying Detail Information (Detail Information Menu) Abbreviations for applications Version information display Version number: Last updated: Checking the unique device ID Entering an installation key to activate an option Setting the Date and Time (Date/ Time Menu) Panel Maintenance (Panel Menu) LCD Bright: Scrn Saver: Touch Beep: Adjusting the system phase Setting the operation switching timing Setting the illegal color limiter Resetting the whole system Initializing memory Carrying out phase adjustments and through mode setting Making the video process setting Video clip adjustment Making vertical blanking width and through mode settings In an HD system, to crop the image in 4:3 mode Setting the reference output Making safe title settings Assigning utility commands To clear a utility command assignment Utility command list Selecting the key memory operating mode Setting the key bus cross-pointhold mode Setting mask and border processing order Making show key settings Setting the Bus Toggle On or Off Setting a Preset Color Mix Enabling or Disabling the Fade-to-BlackFunction Settings Relating to Fader Lever Operations Setting switcher GPI inputs Setting switcher GPI outputs Setting control panel GPI inputs GPI outputs of the control panel Assigning GPI inputs to DCU parallel input ports Setting DCU GPI inputs Assigning GPI outputs to DCU parallel output ports Setting DCU GPI outputs Assigning switcher inputs and outputs to the S-Busspace Making external box settings Making tally group settings Making tally generation settings Making parallel tally settings Making wiring settings Copying tallies Assigning devices to DCU ports Making control settings for devices assigned to ports Making detailed settings for devices assigned to DCU ports Making detailed settings for disk recorders (Sony Disk 9-pinProtocol) Player: Recorder: