Manuals / Sterling / Kitchen Appliance / Food Processor

Sterling 0, 882, 238 manual Annex B Information

Models: 238 0 882

1 43

Download 43 pages 18.2 Kb

Page 4

Annex B Information

The following design information is provided for your reference:

1.	No modifications are allowed to this equipment that could alter the CE compliance
2.	Ambient temperature:		40 degrees Celsius – Maximum (104 degrees Fahrenheit)
3.	Humidity range:	50% relative humidity
4.	Altitude:		Sea level
5.	Environment:		Clean, dust-free and non-explosive
6.	Radiation:		None
7.	Vibration:		Minimal, i.e. machine mounting
8.	Special installation requirements: Clean, dry compressed air 1 cfm @ 60 psi
			(1.7 m³/hr @ 4.14 bar)
9.	Allowable voltage fluctuation:		+/- 10%
10.	Allowable frequency fluctuation:		Continuous	+/- 1%
			Intermittent		+/- 2%

11.N/A

12.Nominal supply voltage: 120/1/60 or 220/1/50/60 (Verify on serial number tag)

13. Earth ground type:	TN (system has one point directly earthed through a protective
	conductor)

14.Power supply should include a neutral power connection.

15.Over-current protection is supplied in the loader, but additional protection should be supplied by the user.

16.The plug on the power cord serves as the electrical disconnect device.

17.Unit is not equipped with three-phase motors.

18.N/A

19.Loader is not equipped with local lighting.

20.Functional identification

21.Loader is equipped with a CE mark

22.Loader is supplied with an operating manual in the language of the destination country.

23.Cable support may be required for power cord, depending on final installation.

24.No one is required to be in the interior of the electrical enclosure during the normal operation of the unit. Only skilled electricians should be inside the enclosure for maintenance.

25.Doors can be opened with a screwdriver, but no keys are required.

26.Two-hand control is not required or provided.

27.All loaders should be moved around and set in a place with a lift truck or equivalent.

28.There are no frequent repetitive cycles that require manual control⎯repetitive functions are automatic while the loader is operating.

29.An inspection report detailing the functional test is included with the loader.

30.The machine is not equipped with cableless controls.

31.Color-coded (harmonized) power cord is sufficient for proper installation.

Page 4

Powder Hopper Loaders

Image 4

Sterling 0, 882, 238 manual Annex B Information

Contents

Powder Hopper Loaders Part Number Bulletin Number CV1-605.2 Effective 4/15/08Write down your Powder Hopper Loaders serialnumbers here for future referenceSafety Considerations Wear SAFETY GLASSES and WORK GLOVESAnnex B Information Table of Contents Installation & SetupGeneral Information Shipping InformationMaintenance TroubleshootingSafety Tag Information Loader Options1-3 Accessories General Information1-1 Introduction 1-2 Equipment Function1-5 Necessary Documents 1-4 Customer Service1-6 System Capabilities 1-7 Models Covered in this Manual Note E Denotes “CE” models, including 220/1/50 operation and CE mark1-8 Standard Features Powder Hopper Loaders2-1 Work Rules Safety2-2 Tools and Equipment Needed 2-4 Safety Considerations 2-3 Mechanical InstallationRead manual thoroughly before installing loader REPORTING A SAFETY DEFECT 2-5 General ResponsibilityNO MATTER WHO YOU ARE… 2-6 Operator Responsibility REMEMBERBEFORE REMOVING, ADJUSTING, OR REPLACING 2-7 Maintenance ResponsibilityPARTS ON A MACHINE, REMEMBER TO DO THE FOLLOWING BLEED all air pressure from system components refer to the Maintenance Section of this manual 2-8 Safety 2-8-2 Safety Circuit StandardsIdentify and locate specific safety devices Understand the proper use of the safety devices provided2-8-4 Safety Device Lock-Outs 2-8-3 Fail Safe Operation2-8-5 Lock-Outs, Plugs, and Other Safety Devices The Line Cord PlugMaximum Machine-Side Throughput 3-1 Unpacking and Inspection Shipping Information3-2 In the Event of Shipping Damages United Parcel Service Shipment 3-3 If the Shipment is Not CompleteParcel Post Shipment 3-4 If the Shipment is Not Correct 3-5 ReturnsDo not return any damaged or incorrect items until you receive shipping instructions from the manufacturerInstallation & Setup 4-1 Safety Considerations4-2 Necessary Tools 4-3 Mounting Powder Hopper Loaders4-5 Mounting Tips 4-6 Attaching the Pickup Wand4-7 Making Compressed Air Connections The manufacturer is not responsible for equipment damage4-8 Making Electrical Connections tight5-1 Pre-Startup Checklist Operation5-2 Operating Sequence Can the material level switch activate without obstruction?AUTOLOADERT M SERIES ONE ON OFF5-3 Starting the Loader 5-4 Changing the Conveying Sequence5-5 Selecting the Most Efficient Loading Sequence Conveying Sequence DIP Switch Chart, Program A0536814 Page5-6 Shutting Down the Hopper Loader Using the Series One Controller 6Maintenance 6-1 Routine MaintenanceCleaning Filters These components are not designed to support the assembly6-2 Replacing Motor Brushes WEAR SAFETY GLASSES BEFORE performing this procedureReplacement and Reassembly Use a stable platform if working above floor levelSeating Motor Brushes Troubleshooting Powder Hopper Loadersnormal normalProblem SolutionPowder Hopper Loaders Cont’d Possible causeLoader Options Special Voltages9-1 Powder Hopper Loader System Component Description Spare Parts9-2-1 Overview Component Identification and Location Technical Assistance 10-1 Contact Information for Technical Assistance10-2 Returned Material Policy 10-2-1 Credit Returns10-2-2 Warranty Returns 11Safety Tag Information 11-1 Powder Hopper Loader Safety Tags11-2 Pushbutton and Keypad Tags Read Operation and Installation Manual Earth Ground11-3 Loader Identification Serial Number Tag Located on back of mixing chamberSeries Powder Hopper Loader Model Number 50E