Manuals / Sterling / Kitchen Appliance / Food Processor

Sterling 882, 0, 238 manual Models Covered in this Manual

Models: 238 0 882

1 43

Page 9

1-7 Models Covered in this Manual

Models are designated by capacity. Powder hopper loaders are available in 1.6 cu. ft. (45.3 liters) capacities and hold approximately 50 lbs. of material.

Powder Hopper		Capacity
Loaders
models	cu. ft.	liters	lbs.	kg
50(E)	1.6	45	50	22

Note: (E) Denotes “CE” models, including 220/1/50 operation and CE mark.

Powder Hopper Loaders

Page 9

Image 9

Sterling 882, 238 manual Models Covered in this Manual, Note E Denotes “CE” models, including 220/1/50 operation and CE mark

Contents

Part Number Bulletin Number CV1-605.2 Effective 4/15/08 Powder Hopper LoadersHopper Loaders serial Write down your Powdernumbers here for future referenceWear SAFETY GLASSES and WORK GLOVES Safety ConsiderationsAnnex B Information Installation & Setup Table of ContentsGeneral Information Shipping InformationTroubleshooting MaintenanceSafety Tag Information Loader OptionsGeneral Information 1-3 Accessories1-1 Introduction 1-2 Equipment Function1-4 Customer Service 1-5 Necessary Documents1-6 System Capabilities Note E Denotes “CE” models, including 220/1/50 operation and CE mark 1-7 Models Covered in this ManualPowder Hopper Loaders 1-8 Standard FeaturesSafety 2-1 Work Rules2-2 Tools and Equipment Needed 2-3 Mechanical Installation 2-4 Safety ConsiderationsRead manual thoroughly before installing loader 2-5 General Responsibility REPORTING A SAFETY DEFECTNO MATTER WHO YOU ARE… REMEMBER 2-6 Operator Responsibility2-7 Maintenance Responsibility BEFORE REMOVING, ADJUSTING, OR REPLACINGPARTS ON A MACHINE, REMEMBER TO DO THE FOLLOWING BLEED all air pressure from system components refer to the Maintenance Section of this manual 2-8-2 Safety Circuit Standards 2-8 SafetyIdentify and locate specific safety devices Understand the proper use of the safety devices provided2-8-3 Fail Safe Operation 2-8-4 Safety Device Lock-OutsThe Line Cord Plug 2-8-5 Lock-Outs, Plugs, and Other Safety DevicesMaximum Machine-Side Throughput Shipping Information 3-1 Unpacking and Inspection3-2 In the Event of Shipping Damages 3-3 If the Shipment is Not Complete United Parcel Service ShipmentParcel Post Shipment 3-5 Returns 3-4 If the Shipment is Not CorrectDo not return any damaged or incorrect items until you receive shipping instructions from the manufacturer4-1 Safety Considerations Installation & Setup4-2 Necessary Tools 4-3 Mounting Powder Hopper Loaders4-6 Attaching the Pickup Wand 4-5 Mounting Tips4-7 Making Compressed Air Connections The manufacturer is not responsible for equipment damagetight 4-8 Making Electrical ConnectionsOperation 5-1 Pre-Startup Checklist5-2 Operating Sequence Can the material level switch activate without obstruction?SERIES ONE ON OFF AUTOLOADERT M5-4 Changing the Conveying Sequence 5-3 Starting the Loader5-5 Selecting the Most Efficient Loading Sequence Page Conveying Sequence DIP Switch Chart, Program A05368145-6 Shutting Down the Hopper Loader Using the Series One Controller 6-1 Routine Maintenance 6MaintenanceCleaning Filters These components are not designed to support the assemblyWEAR SAFETY GLASSES BEFORE performing this procedure 6-2 Replacing Motor BrushesReplacement and Reassembly Use a stable platform if working above floor levelSeating Motor Brushes Powder Hopper Loaders Troubleshootingnormal normalSolution ProblemPowder Hopper Loaders Cont’d Possible causeSpecial Voltages Loader OptionsSpare Parts 9-1 Powder Hopper Loader System Component Description9-2-1 Overview Component Identification and Location 10-1 Contact Information for Technical Assistance Technical Assistance10-2 Returned Material Policy 10-2-1 Credit Returns10-2-2 Warranty Returns 11-1 Powder Hopper Loader Safety Tags 11Safety Tag Information11-2 Pushbutton and Keypad Tags Read Operation and Installation Manual Earth GroundLocated on back of mixing chamber 11-3 Loader Identification Serial Number TagSeries Powder Hopper Loader Model Number 50E