Manuals / Sub-Zero / Kitchen Appliance / Refrigerator

Sub-Zero ICB700TCI, ICB700TR L E V E L The Unit, M O L D I N G I N S Ta L L At I O N, Top Molding

Models: ICB700TR ICB700TCI ICB700TFI

1 104

Download 104 pages 47.94 Kb

Page 16

L E V E L THE UNIT

I N T E G R AT E D INSTALLATION INSTRUCTIONS

L E V E L THE UNIT

M O L D I N G I N S TA L L AT I O N

Level the Integrated unit by turning the front leveling legs clockwise to raise the unit, or counterclockwise to lower it. To assist you in adjusting the front leveling legs up or down, use a standard screwdriver blade and place it in the front leveling leg as shown in illustration 6 below.

The rear leveling legs are adjusted from the front of the base by turning the Phillips head screw. Refer to illustration 7.

IMPORTANT NOTE: The rear leveling legs will only move 2 mm for every 18 revolutions on the Phillips head screw. Do not over torque. Use the lowest torque setting on any power screwdriver. Do not turn the rear leveling legs by hand. Damage will occur if you turn these legs.

Once the unit is leveled, secure the unit in place by using the side mounting clips and #8 x 12,7 mm screws provided.

To reduce the possibility of the unit tipping forward, the front leveling legs must be in contact with the floor.

The decorative white molding strips for the side and top of the unit can be snapped into place. The top molding strip used on Integrated tall units, must be installed before the side molding can be attached. The top molding strip is held in place by double-sided velcro fasteners. Refer to illustration 8 below for positioning of the top molding.

Illustration 9 shows side molding installation for tall units. Installation of the side molding for base units is the same. For installations where units are side by side, refer to Dual Installations on page 21.

NOTE: The molding strips may be painted to match the surrounding cabinetry, if you choose. Follow these easy steps:

Rough up the surface to be painted with fine grit sandpaper.

Wipe with alcohol to ensure that the surface is clean and dry.

Use an appliance or industrial grade, oil base, high gloss enamel paint.

Top Molding

Illus. 6

Illus. 7

Illus. 8

Illus. 9

16

Image 16

Sub-Zero ICB700TCI, ICB700TFI, ICB700TR L E V E L The Unit, M O L D I N G I N S Ta L L At I O N, Top Molding

Contents

INSTALLATION INSTRUCTIONS INSTRUCCIONES DE INSTALACIÓN INSTRUCTIONS D’INSTALLATIONISTRUZIONI PER L’INSTALLAZIONE INSTALLATIONSANWEISUNGEN INTEGRATED REFRIGERATIONPage E N G L I S H E S P Ã N O LF R A N Ç A I S I TA L I A N OInstallation Recommendations Installation SpecificationsInstallation Instructions Installation ChecklistTOOLS AND MATERIALS REQUIRED I N S TA L L AT I O N RECOMMENDATIONSSITE PREPARATION Overall Dimensions Width686 mm HeightOverall Dimensions Width914 mm HeightOverall Dimensions Width686 mm HeightE L E C T R I C A L REQUIREMENTS P LU M B I N G REQUIREMENTS DOOR AND DRAWER PANELS SIDE PANELSU N PA C K I N G A N D M O V I N G A N T I - T I P B R AC K E T I N S TA L L AT I O NWOOD FLOOR APPLICATIONS CONCRETE FLOOR APPLICATIONSDimension A A N T I - T I P B R AC K E T I N S TA L L AT I O NA N T I - T I P BLOCKING BRACKET INSTALL CONCRETE WEDGE ANCHORSP O S I T I O N THE UNIT P O S I T I ON THE UNIT On/OffM O L D I N G I N S TA L L AT I O N L E V E L THE UNITTop Molding QUICK CONNECT WATER VALVE K I C K P L AT E / G R I L L E INSTALLATION Back Of Door PanelGap On Side According ToDOOR PANEL INSTALLATION DIMENSIONS MAY VARY606 mm* FOR 686 mm WIDE UNITS 835 mm* FOR 914 mm WIDE UNITSDRAWER PANEL INSTALLATION Top Of Template Flush With Top Of Drawer PanelGap On Side Edges Will Vary9 0 - D E G R E E DOOR STOP INSTALLATION CHECKLIST I N S TA L L AT I O N C H E C K L I S THas the kickplate/grille been installed properly? I N S TA L L AT I O N C H E C K L I S TS E R V I C E I N F O R M AT I O N S E R V I C E I N F O R M AT I O N Recomendaciones de instalación Especificaciones de la instalaciónInstrucciones de instalación Lista de comprobación de la instalaciónNECESARIOS HERRAMIENTAS Y MATERIALESRECOMENDACIONES DE INSTALACIÓN I N T E G R A B L E Medidas totales Anchura686 mm AlturaMedidas totales Anchura914 mm AlturaMedidas totales Anchura686 mm AlturaREQUISITOS E L É C T R I C O S REQUISITOS DE F O N T A N E R Í A PANELES LATERALES PANELES DE LA PUERTA Y LOSCAJONES D E S E M B A L A J E Y D E S P L A Z A INSTALACIÓN DEL S O P O RT EM I E N TO A N T I V U E LCOA N T I - V U E LCO APLICACIONES EN SUELO DEMADERA HORMIGÓNINSTALACIÓN DE ANCLAJES DE EXPANSIÓN PARA HORMIGÓN A N T I V U E LC OC O LO C A C I Ó N DE LA UNIDAD C O LO C A C I Ó N DE LA UNIDAD INSTALACIÓN DE LA M O L D U R A N I V E L A C I Ó N DE LA UNIDADMoldura superior CONEXIÓN A LA TO M A D E A G UA VÁLVULA DE AGUA DE CONEXIÓN RÁPIDAINSTALACIÓN DEL Z Ó C A LO / R E J I L L A Vista trasera del panel de la puertaEl espacio en los bordesPUERTA INSTALACIÓN DEL PANEL DE LAVISTA DESDE LA PARTE TRASERA DE LOS PANELES INSTALACIÓN DE LOS PANELES DE LOS CAJONES Parte superiorde la plantilla alineada El espacioINSTRUCCIONES DE INSTALACIÓN I N T E G R A B L E L I S TA D E CO M P R O BA C I Ó N DE LA INSTALACIÓN I N S TA L A C I Ó NLISTA DE COMPROBACIÓN DE LA INSTALACIÓNINFORMACIÓN SOBRE EL M A N T E N I M I E N TO N I M I E N TORecommandations d’installation Spécifications d’installationInstructions d’installation Liste de contrôle de l’installationOUTILS ET MATERIAUX REQUIS PREPARATION DE L’EMPLACEMENTREMARQUE IMPORTANTE Les bords Dimensions hors-tout Largeur686 mm HauteurDimensions hors-tout Largeur914 mm HauteurDimensions hors-tout Largeur686 mm HauteurCONFIGURATION E L E C T R I Q U E REMARQUE IMPORTANTE Ne faites pas passer la conduite d’eau devant le plateau du compresseur. Celui-ci doit pouvoir glisser vers l’avant en cas de réparation PANNEAUX DE PORTE ET DE TIROIR PANNEAUX LATERAUXREMARQUE IMPORTANTE Une partie de REMARQUE IMPORTANTE Si vous ne fixezREMARQUE IMPORTANTE Ne jetez pas D E B A L L A G E ET D E P L A C E M E N T D E L’ A P PA R E I LA N T I B A S C U L E M E N T SUR UN SOL EN BETON SUR UN PLANCHER DE BOISA N T I B A S C U L E M E N T SUPPORT A N T I B A S C U L E M E N T INSTALLATION DES ANCRAGES A CALE POUR SOL EN BETONM I S E E N P L A C E DE L’APPAREIL REMARQUE IMPORTANTE Une fois l’appareil REMARQUE IMPORTANTE Si, pour quelqueREMARQUE IMPORTANTE Sous l’appareil M I S E E N P L A C E DE L’APPAREILM I S E A N I V E AU DE L’APPAREIL P O S E DES M O U L U R E SD ’ E A U ROBINET DE PRISE D’EAU ARACCORD RAPIDE REMARQUE IMPORTANTE La fabrique deINSTALLATION DE L A P L I N T H E G R I L L E POSE DES P A N N E A UArrière du panneau de porte L’espace sur lesREMARQUE IMPORTANTE Le gabarit POSE DES PANNEAUX DE PORTEPOSE DES P A N N E A U POSE DE PANNEAU DE TIROIR POSE DES P A N N E A ULa dessus du gabarit affleure au dessus du panneau de tiroir L’espace sur lesA R R E T D E P O RT E A 90 DEGRES INSTALLATIONS C O N J O I N T E SPOSE DES P A N N E A U L I S T E D E CO N T R O L E DE L’INSTALLATION L’INSTALLATIOND E L ’ I N S T A L L A T I O N LISTE DE CONTROLE DESub-Zero, Inc. Tous droits réservés Site Internet subzero.comConsigli per l’installazione Specifiche per l’installazioneIstruzioni per l’installazione Check list per l’installazionePREPARAZIONE DEL SITO ATTREZZI E MATERIALE RICHIESTICONSIGLI PER L’INSTALLAZIONE I N T E G R A T A Dimensioni generali D I M E N S I O N I G E N E R A LU N I T À V E R T I C A L E S P E C I F I C H EDimensioni generali Altezza2.032 mm ProfonditàDimensioni generali Larghezza686 mm AltezzaCOLLEGAMENTO E L E T T R I C O Page PANNELLI PER PORTE E CASSETTI PANNELLI LATERALID I S I M BA L L AG G I O E S P O S TA INSTALLAZIONE D E L LA BA R R AM E N TO APPLICAZIONE PER PAVIMENTI IN LEGNOCEMENTO INSTALLAZIONE D E L LA BA R R ABARRA DI BLOCCO A N T I R I B A L T A M E N T O INSTALLAZIONE DEI TASSELLI PER CEMENTOP O S I Z I O N A M E N TO DELL’UNITÀ ISTRUZIONI PER L’INSTALLAZIONE I N T E G R ATA P O S I Z I O N A M E N TO DELL’UNITÀL I V E L L A M E N TO DELL’UNITÀ INSTALLAZIONE DELLA M O DA N AT U R AModanatura superiore VALVOLA IDRICA COLLEGAMENTO RAPIDO DELLAin PEX INSTALLAZIONE D I Z O CCO LO G R I G L I A INSTALLAZIONE D E I PA N N E L LRetro del pannello porta Lo spazio sui bordi laterali varia secondo il designINSTALLAZIONE D E I PA N N E L L INSTALLAZIONE DEL PANNELLO DELLA PORTAVISTA DAL RETRO DEI PANNELLI INSTALLAZIONE DEI PANNELLI PER CASSETTI INSTALLAZIONE D E I PA N N E L LSommità del modello a filo con la sommitàF E R M A P O RTA DA 90 GRADI INSTALLAZIONE D E I PA N N E L LCHECK LIST PER L’INSTALLAZIONE CHECK LIST PER L ’ I N S T A L L A Z I O N ELo zoccolo/la griglia sono stati installati correttamente? CHECK LIST PER L ’ I N S T A L L A Z I O N EINFORMAZIONI PER IL S E R V I Z I O D I A S S I S T E N Z A A S S I S T E N Z AVORSICHT ACHTUNGEmpfehlungen zur Installation InstallationsspezifikationenVORBEREITUNG DES INSTALLATIONS EMPFEHLUNGEN ZUR I N S T A L L A T I O NERFORDERLICHE WERKZEUGE UND MATERIALIENGesamtabmessungen Breite686 mm HöheGesamtabmessungen Breite914 mm HöheGesamtabmessungen Breite686 mm HöheACHTUNG VORSICHTACHTUNG E L E K T R O V O R A U S S E T Z U N G E NVO R AU S S E T Z U N G E N FÜR DIE TÜR - UND SCHUBLADENPLATTEN D E KO R P L AT T E NSEITENPLATTEN INSTALLATION DER K I P P S C H U T Z H A L verhindern und eine stabile Installation zuACHTUNG VORSICHTACHTUNG S C H U T Z H A L T E R U N GH O L Z B O D E N A N W E N D U N G E N B E TO N B O D E N A N W E N D U N G E NBETONANKERKEILE INSTALLIEREN VORSICHTVORSICHT ANWEISUNGEN ZUR I N T E G R I E RT E NACHTUNG P O S I T I O N I E R E N DES GERÄTSStromzufuhr zur Steckdose unterbrechen WICHTIGER HINWEIS Der Boden unter demACHTUNG N I V E L L I E R E N DES GERÄTSI N S TA L L AT I O N D E R Z I E R L E I S T E N Obere LeisteACHTUNG ANSCHLUSS DER WA S S E R L E I T U N GSCHNELLTRENN - WASSERVENTIL WICHTIGER HINWEIS Die WasserzufuhrS O C K E L L E I S T E / G I T T E R WICHTIGER HINWEIS Am Gerät muss durchVORSICHT INSTALLATION DER TÜRPLATTEANSICHT VON RÜCKSEITE DER PLATTEN INSTALLATION DER SCHUBLADE VORSICHTBei einer kleineren Laibung zwischen Schränken und dem Gerät besteht dieVORSICHT INSTALLATION DER P L AT T ED O P P E L I N S TA L L AT I O N E N I N S TA L L AT I O N S C H E C K L I S T E INSTALLATIONSCHECKLISTEI N S TA L L AT I O N S C H E C K L I S T E ACHTUNG S E R V I C E I N F O R M AT I O N E NS E R V I C E I N F O R M AT I O N E N KO N TA K T I N - F O R M AT I O N E NSUB-ZERO, INC PO BOX MADISON, WI 53744 USA SUBZERO.COM 7 0 0 4 5 5 1 1 1 / 2 0 0