Performance Specifications | Sun Microsystems 806-2989-10 specification

Performance Specifications

TABLE A-2Performance Specifications

Feature	Specification

PCI clock	33/66 MHz max
PCI data burst transfer rate	up to 64-byte bursts
PCI data/address width	32/64 -bit
PCI modes	Master/slave
1 GBit/s, 850 nm	1000 Mbps (full duplex)

Physical Characteristics

TABLE A-3	Physical Characteristics

Dimension	Measurement

Length	6.8 inches
Width	4.2 inches

Power Requirements

TABLE A-4Power Requirements

Specification	Measurement

Maximum power consumption	14 watts
Voltage	3.3V and 5V

52 Sun GigaSwift Ethernet Adapter Installation and User’s Guide • February 2001

Image 72

Sun Microsystems 806-2989-10 manual Performance Specifications, Physical Characteristics, Power Requirements

Contents

Sun GigaSwift Ethernet Adapter Installation User’s Guide Please Recycle Regulatory Compliance Statements FCC Class a NoticeFCC Class B Notice ICES-003 Class a Notice Avis NMB-003, Classe a ICES-003 Class B Notice Avis NMB-003, Classe B Bsmi Class a Notice Page Declaration of Conformity Product NameSun GigaSwift Ethernet UTP Adapter X1150AEN550221998 / CISPR221997 Page Contents Configuring Driver Parameters Configuring VLANsSpecifications Diagnostic Software and Troubleshooting Issues IndexPage Figures Page Tables Page Preface How This Book Is Organized Using Unix Commands Typographic Conventions Accessing Sun Documentation Online Shell PromptsRelated Documentation Ordering Sun Documentation Sun Welcomes Your Comments Product Overview Hardware Overview Sun GigaSwift Ethernet UTP Adapter 1Sun GigaSwift Ethernet UTP Adapter Product Features Hardware and Software RequirementsKey Protocols and Interfaces Diagnostic Support Installing the Adapter Installing the Driver SoftwareBecome superuser 1Files and Directories on the CD-ROM See -1to identify the optional packages Installing the Adapter Without Dynamic Reconfiguration To Install the Adapter To Verify the Installation 1Cat-5 Twisted-Pair Cable List the network devices on your system View the .properties file for a list of device properties Ok .properties Setting the local-mac-addressProperty To Set the GigaSwift Ethernet Device Primary Boot Device Rebooting the System Installing the Adapter With Dynamic Reconfiguration To Install an Adapter in a Dynamic Reconfiguration System If the status of the slot is not empty or disconnected, type Configure the adapter and slot Reconfigure the devices on the adapterConnect the adapter and slot Network Configuration Configuring the Network Host Files Etc/hostname.ce1 # cat /etc/hosts To Set Up a Diskless Client on a GigaSwift Ethernet Network Edit the hosts in the diskless client’s root directory Network Configuration # grep clientname /etc/bootparams Find the root directory of the client system Proceed with the Solaris operating environment installation Shut down and halt the client system # pkginfo grep SUNWce Configuring Driver Parameters GigaSwift Ethernet Device Driver Parameters Driver Parameter Values and Definitions 1ce Driver Parameter, Status, and Descriptions Operational Mode Parameters Operational Mode Parameters Flow Control Parameters 3Read-Write Flow Control Keyword Descriptions Gigabit Forced Mode Parameter 4Forced Mode ParameterInterpacket Gap Parameters 5defines the enableipg0 and ipg0 parameters 5Parameters Defining enableipg0 and ipg0 Interrupt Parameters Random Early Drop Parameters7RX Blanking Register for Alias Read 8RX Random Early Detecting 8-Bit Vectors PCI Bus Interface Parameters 9PCI Bus Interface Parameters Setting ce Driver Parameters Setting Parameters Using the ndd Utility To Specify Device Instances for the ndd Utility Noninteractive and Interactive ModesUse the instance number to select the device Using the ndd Utility in Interactive Mode To modify a parameter value, use the -setoption Setting the Autonegotiation Mode Setting Parameters Using the ce.conf File To Disable Autonegotiation ModeSet the advautonegcap parameter to To Set Driver Parameters Using a ce.conf File Etc/pathtoinst file GigaSwift Ethernet Driver Operating Statistics 10Read-Only ce Device Capabilities Reporting the Link Partner Capabilities 11Read-Only Link Partner Capabilities 12Transmit and Receive Parameters Rxnewpages rxnewhdrpgs To Check Link Partner Settings As superuser, type the netstat -kcommandPage Configuring VLANs An Overview of VLANs 1shows an example network that uses VLANs Configuring VLANs To Configure Static VLANs 2Ethernet Tag Header Format # ifconfig ce123000 plumb up # ifconfig ce224000 plumb up Page Specifications ConnectorsTable A-1Cat-5 Connector Link Characteristics Performance Specifications Physical CharacteristicsPower Requirements Table A-2Performance Specifications Diagnostic Software Troubleshooting Issues SunVTS Diagnostic Software Using the OpenBoot Prom FCode Self- Test Running the Ethernet FCode Self-Test DiagnosticReset the system Shut down the system Type show-netsto display the list of devices Troubleshooting Issues Set the auto-boot?configuration parameter to trueReset and reboot the system Type the following to apply and save your changes Adv1000fdxcap Adv1000hdxcap AdvpauseTX AdvpauseRX Symbols Index