6Opening the Injector/Ejector Latch | Sun Microsystems CP3000

FIGURE 1-6Opening the Injector/Ejector Latch

Figure Legend

1Fully In (IN) When IN, the module communicates to the shelf manager that the module is not in the hot-swap state, and the shelf manager communicates with the MMC. This position is for normal operation.

2Half Way (HW) When in the HW position, the hot-swap sequence is initiated. The MMC sends a hot-swap event to the shelf manager.

Out (OUT) When OUT, the latching mechanism is released and the module can be extracted. Wait

3for the Hot-Swap LED to stop blinking before pulling the latch all the way out.

Chapter 1 Getting Started 1-15

Image 25

Sun Microsystems CP3000 manual 6Opening the Injector/Ejector Latch

Contents

For the AMC.1-HDD SAS Disk Please Recycle Contents Managing the AMC Overview Connectors and Ports Configuring the AMCEnvironment Specifications Agency Certifications Index Index-1 Typographic Conventions Preface Third-Party Web Sites Related Documentation Sun Welcomes Your Comments Page Getting Started Important Safety Information for Sun Hardware Systems Operating Systems Compatibility System RequirementsChassis Compatibility Blade Server Compatibility Electrical and Environmental Unpacking Handling AMCs 1AMC.1-HDD SAS Disk Faceplate AMC Faceplate 1AMC Status LEDs AMC LEDs 2Hot-Swap Blue LED States Removing an AMC Removing and Installing AMCsShut down the payload OS Hot-Swap LED starts blinking 2Deactivating the AMC 3Removing the AMC Remove the AMC 4Front Cable Management Bracket in Lower Position Removing a Blade Server and AMC Remove the filler panel, if necessary Installing an AMC 5Sample Top View Obtain the AMC card from the ship kit 6Opening the Injector/Ejector Latch Page 7Inserting the AMC Into a Blade Server Push the ejector latch in fully To Enable AMC Port 3 Driven by Port 2 of SAS Controller To Enable AMC Port 2 Driven by Port 1 of SAS ControllerPower on the system, if necessary Enabling and Disabling SAS Ports To Disable AMC Port 3 Driven by Port 2 of SAS Controller To Disable AMC Port 2 Driven by Port 1 of SAS ControllerPage Overview Features Key Components Power RegulatorHard Drive Disk Flash SAS ControllerModule Management Controller MMC Faceplate and LEDs Port ConnectorsLEDs OOS Technical Support and Warranty Functional DiagramPage 4Sun Netra CP3000 AMC.1-HDD SAS disk Barcode Labeling Disposal Managing the AMC Monitoring and Control Functions Supported Ipmi CommandsIpmi Controller 1Supported Ipmi Commands 2Standard FRU Data Records FRU Information 3Threshold Sensors Sensors Readme files within the download package Firmware and Software Upgrades Configuring the AMC Boot Bios Utility Configuration Tools Launching the Boot Bios Utility Features and ConfigurationsPress Ctrl C Page 2Adapter Properties Menu OpenBoot Bios Enabling and Disabling Channel Ports Extensible Firmware Interface EFI Connectors and Ports Connector Pinouts Connector Locations and AssignmentsTable A-1Pin Assignments Appendix a Connectors and Ports SAS Controller Ports 1AMC e-Keying Port Assignments Keying PortsPage Environment Specifications Table B-2Environmental Specifications Table B-1Electrical SpecificationsElectrical and Environmental Electrical RPM Table B-3MTBF Values by Temperature Absolute Maximum Ratings ReliabilityNormal Operating Ranges AMC.1-HDD SAS disk PCB Dimensions Board Dimensions and WeightMechanical Page Agency Certifications NEBS/ETSI CE Certification Safety 1 EN 55022 Emissions Emissions Test Regulations2 EN 55024 Immunity FCC USA Regulatory InformationIndustry Canada Canada Page Numerics Index NEBS/ETSI, C-2