Extensible Firmware Interface EFI | Sun Microsystems CP3000 specification

4.4Extensible Firmware Interface (EFI)

BIOS

The AMC.1-HDD SAS disk includes an EFI boot services driver for use with ATCA blades that feature Intel® IA64 processors. Additional information is available at http://www.lsi.com.

4.5Enabling and Disabling Channel Ports

As shipped from the factory, the AMC.1-HDD SAS disk will not drive AMC channel ports, due to the default “disable” setting. You can enable these ports using lsiutil, a command line utility. For instructions, see Section 1.7, “Enabling and Disabling SAS Ports” on page 1-18.

4-6Sun Netra CP3000 Advanced Mezzanine Card PCIe Hard Drive and SAS Controller User’s Guide • March 2010

Image 52

Sun Microsystems CP3000 manual Extensible Firmware Interface EFI, Enabling and Disabling Channel Ports

Contents

For the AMC.1-HDD SAS Disk Please Recycle Contents Overview Managing the AMC Configuring the AMC Connectors and PortsEnvironment Specifications Agency Certifications Index Index-1 Preface Typographic Conventions Related Documentation Third-Party Web Sites Sun Welcomes Your Comments Page Important Safety Information for Sun Hardware Systems Getting Started System Requirements Operating Systems CompatibilityChassis Compatibility Blade Server Compatibility Unpacking Electrical and Environmental Handling AMCs AMC Faceplate 1AMC.1-HDD SAS Disk Faceplate AMC LEDs 1AMC Status LEDs 2Hot-Swap Blue LED States Removing an AMC Removing and Installing AMCsShut down the payload OS Hot-Swap LED starts blinking 2Deactivating the AMC Remove the AMC 3Removing the AMC Removing a Blade Server and AMC 4Front Cable Management Bracket in Lower Position Installing an AMC Remove the filler panel, if necessary Obtain the AMC card from the ship kit 5Sample Top View 6Opening the Injector/Ejector Latch Page Push the ejector latch in fully 7Inserting the AMC Into a Blade Server To Enable AMC Port 2 Driven by Port 1 of SAS Controller To Enable AMC Port 3 Driven by Port 2 of SAS ControllerPower on the system, if necessary Enabling and Disabling SAS Ports To Disable AMC Port 2 Driven by Port 1 of SAS Controller To Disable AMC Port 3 Driven by Port 2 of SAS ControllerPage Overview Features Key Components Power RegulatorHard Drive Disk Flash SAS ControllerModule Management Controller MMC Faceplate and LEDs Port ConnectorsLEDs OOS Functional Diagram Technical Support and WarrantyPage 4Sun Netra CP3000 AMC.1-HDD SAS disk Barcode Labeling Disposal Managing the AMC Monitoring and Control Functions Supported Ipmi CommandsIpmi Controller 1Supported Ipmi Commands FRU Information 2Standard FRU Data Records Sensors 3Threshold Sensors Firmware and Software Upgrades Readme files within the download package Configuring the AMC Configuration Tools Boot Bios Utility Launching the Boot Bios Utility Features and ConfigurationsPress Ctrl C Page OpenBoot Bios 2Adapter Properties Menu Extensible Firmware Interface EFI Enabling and Disabling Channel Ports Connectors and Ports Connector Pinouts Connector Locations and AssignmentsTable A-1Pin Assignments Appendix a Connectors and Ports SAS Controller Ports Keying Ports 1AMC e-Keying Port AssignmentsPage Environment Specifications Table B-1Electrical Specifications Table B-2Environmental SpecificationsElectrical and Environmental Electrical Table B-3MTBF Values by Temperature RPM Absolute Maximum Ratings ReliabilityNormal Operating Ranges AMC.1-HDD SAS disk PCB Dimensions Board Dimensions and WeightMechanical Page Agency Certifications CE Certification NEBS/ETSI Safety 1 EN 55022 Emissions Emissions Test Regulations2 EN 55024 Immunity FCC USA Regulatory InformationIndustry Canada Canada Page Index Numerics NEBS/ETSI, C-2