Connector Deﬁnitions, NMI Header | SUPER MICRO Computer 6026TT-GTRF

SUPERSERVER 6026TT-GTRF/GIBXRF/GIBQRF User's Manual

5-7 Connector Deﬁnitions

Front Panel Accessible Add-on Card Header (JF2)

The JF2 add-on card header provides front access to the power supply, Serial ATA and Front Panel Control connections for the X8DTT-H Series serverboard. Plug an Add-On card into this header to use the functions indicated above. This header is designed speciﬁcally for a hot plug 2U daughter card..

NMI Header

The non-maskable interrupt header is lo- cated at JNMI1. Refer to the table on the right for pin deﬁnitions.

NMI Button

Pin Deﬁnitions

Pin# Deﬁnition

1Control

2Ground

Internal Buzzer

The Internal Buzzer, located at JSPK1, can be used to provide audible alarms for various beep codes. See the table on the right for pin deﬁnitions..

IPMB I2C SMB

A System Management Bus header for the IPMI slot is located at IPMB. Connect the appropriate cable here to use the IPMB I2C connection on your system. See the table on the right for pin deﬁnitions..

Internal Buzzer

Pin Deﬁnitions

Pin#				Deﬁnitions
Pin 1		Pos. (+)		Beep In
Pin 1		Pos. (+)		Beep In
Pin 2		Neg. (-)		Alarm Speaker
Pin 2		Neg. (-)		Alarm Speaker

SMB Header

Pin Deﬁnitions

Pin# Deﬁnition

1Data

2Ground

3Clock

4No Connection

5-12

Image 46

SUPER MICRO Computer 6026TT-GTRF Connector Deﬁnitions, Front Panel Accessible Add-on Card Header JF2, NMI Header

Contents

Super Manual Revision Release Date November 16 About This Manual PrefaceManual Organization Advanced Chassis Setup System SafetyAdvanced Serverboard Setup Bios Preface Table of Contents System Interface Appendix a Bios Error Beep Codes Chapter Introduction Overview Serial ATA Serverboard FeaturesProcessors Memory PCI Expansion Slots Graphics Controller Other FeaturesOnboard Controllers/Ports InﬁniBand Intel 5520 Chipset System Block Diagram Server Chassis Features Nodes 2U Twin System NotesGPU Subsystem Sata Backplane/Drives Europe Contacting SupermicroHeadquarters Asia-PaciﬁcPage Preparing for Setup Chapter Server InstallationUnpacking the System Choosing a Setup Location Ambient Operating Temperature Rack Mounting Considerations Removing the Protective Film Removing the Protective Film Separating the Sections of the Rack Rails Rail AssemblyRack Mounting Instructions Separating the Inner and Outer Rails Installing the Inner Rail Extensions Installing the Inner Rails Installing the Outer Rails to the Rack Outer Rack Rails Installing Into the Rack Installing the Chassis into a Rack Accessing the Inside of a Node Figure Checking the Serverboard SetupChecking the Components and Setup Checking the Sata drives Preparing to Power OnProviding Power Checking the Airﬂow Removing a Node from the System Page Chapter System Interface PowerControl Panel Buttons Sata Drive Carrier LEDs Control Panel LEDsOverheat/Fan Fail Chapter System Safety Electrical Safety Precautions General Safety Precautions ESD Precautions Operating Precautions Installing the Onboard Battery Chapter Advanced Serverboard Setup Handling the Serverboard I/O Ports I/O Ports Processor and Heatsink Installation Installing LGA1366 Processors CPU Installing a CPU Heatsink Removing the Heatsink Installing Memory Modules Installing MemoryMemory Support Dimm Installation Notch Front View Adding PCI Cards PCI Card InstallationPCI Express Slot Serverboard Details LE2 Serverboard Quick Reference Connector DescriptionJumper Description NMI Header Connector DeﬁnitionsFront Panel Accessible Add-on Card Header JF2 Internal Buzzer Fan Header Video ConnectorUniversal Serial Bus USB Ethernet Ports InﬁniBand Connection X8DTT-HIBXF+/ HIBQF+ Unit Identiﬁer Switches System ResetSerial Ports Cmos Clear Jumper SettingsTo Clear Cmos Watch Dog Enable/Disable LAN1/LAN2 Enable/DisableVGA Enable/Disable Onboard Power LED Onboard IndicatorsInﬁniBand LED Indicators LEB1/LEB2 LAN1/LAN2 LEDs Rear UID LED LE4 Serial ATA PortsBMC Activity LED LE2 Serial ATA Connections Installing Additional Drivers 12 Conﬁguring Supero Doctor Page Chapter Advanced Chassis Setup Control Panel System Fans System Fan Failure Fan ConﬁgurationChanging a System Fan Installing a Hard Drive into the Drive Carrier Hard Drive Installation/RemovalInstalling and Removing Hard Drives Overview Installing/Removing Hot-swap Drives Removing a Dummy Drive Tray Node a Node B Node Installation/Removal Removing a Node Removing a System Node Installing an Air Shroud Installing the Air ShroudsPower Supply Removing/Replacing the Power Supply Figure Removing the Power Supply Release Tab Chapter Starting Bios Setup UtilityHow To Change the Conﬁguration Data Introduction System Overview Main SetupStarting the Setup Utility System Time/System Date Processor Bios Build DateAMI Bios Core Version CPU Type Advanced Setup Conﬁgurations Xboot Features XPower Conﬁguration XProcessor and Clock Options Active Processor Cores Hardware Prefetcher Available when supported by the CPUC1E Support Intel Eist Technology XAdvanced Chipset Control Xcpu Bridge Conﬁguration QPI L0s and L1 Memory ModeMemory ECC Error Threshold Memory Frequency Inlet Temperature Hysteresis TemperatureGuardband Temperature Temperature Rise XNorth Bridge Conﬁguration XSouthBridge Conﬁguration XIDE/SATA Conﬁguration SATA#2 Conﬁguration LBA/Large ModePIO Mode Type DMA Mode XPCI/PnP Conﬁguration XRemote Access Conﬁguration XSuper IO Device Conﬁguration XHardware Health Monitor Sredir Memory Display DelayCPU Overheat Alarm Terminal Type CPU Temperature/System Temperature CPU Temperature Fan Speed Control Monitor Acpi Version Features Acpi Apic SupportXacpi Conﬁguration Fan1 ~ Fan 4 Reading XGeneral Whea Conﬁguration Xipmi Conﬁguration X8DTT-HF/-HIBXF/-HIBQF Only XIP Address Conﬁguration XView BMC System Event LogXSet LAN Conﬁguration Parameter Selector Xmac Address Conﬁguration XSubnet Mask Conﬁguration Current Subnet Mask in BMC XGateway Address ConﬁgurationSubnet Mask Gateway Address Security Settings Xdmi Event Log Password Check Boot ConﬁgurationXBoot Device Priority Boot Sector Virus Protection XRemovable Drives XHard Disk DrivesXCD/DVD Drives Bios Recovery Exit Options How to Recover the Amibios Image the Main Bios Block Boot Sector Recovery from a USB Device Boot Sector Recovery from a Serial Port Serial Flash How to use Serial Flash for Boot Sector RecoveryPage Page Bios Error Beep Codes Appendix a Bios Error Beep CodesBios Error Beep Codes Page Appendix B Installing Windows Installing Windows for a RAID System Installing Windows for a Non-RAID System Bios Appendix C System Speciﬁcations Chassis Regulatory Compliance