Teledyne BDS-3960 - page 36

Installation BDS 3960

Teledyne Analytical Instruments 36

Threshold Alarm 2:

• Can be configured as high (actuates when concentration

is above threshold), or low (actuates when concentration

is below threshold).

• Can be configured as failsafe or nonfailsafe.

• Can be configured as latching or nonlatching.

• Can be configured out (defeated).

System Alarm:

• Actuates when DC power supplied to circuits is

unacceptable in one or more parameters. Permanently

configured as failsafe and latching. Cannot be defeated.

Actuates if communication with PPC fails.

Further detail can be found in Chapter 4, Section 4-5.

Table 3-2: Alarm Relay Contact Pins

Pin Contact

45 Threshold Alarm 1, normally closed contact

28 Threshold Alarm 1, moving contact

46 Threshold Alarm 1, normally open contact

42 Threshold Alarm 2, normally closed contact

44 Threshold Alarm 2, moving contact

43 Threshold Alarm 2, normally open contact

36 System Alarm, normally closed contact

20 System Alarm, moving contact

37 System Alarm, normally open contact

Digital Remote Cal Inputs: Accept 0 V (off) or 24 V dc (on) inputs for

remote control of calibration. (See Remote Calibration Protocol below.)

See Table 3-3 for pin connections.

Contents

Main BDS 3960 Teledyne Analytical Instruments ii Copyright 2002 Teledyne Analytical Instruments Specific Model Information Safety Messages Page Table of Contents Page Page List of Figures Page List of Tables DANGER COMBUSTIBLE GAS USAGE WARNING Introduction 1.1 Overview 1.2 Typical Applications 1.3 Main Features of the Analyzer 1.4 Front Panel (Operator Interface) Page 1.5 Rear Panel (Equipment Interface) Page Operational Theory 2.1 Introduction 2.2 BDS Sensor 2.2.1 Principles of Operation Page Page 2.2.2 Gas Flow Rate 2.2.3 Gas Pressure 2.2.4 Temperature effect 2.2.5 Recovery from High Level Oxygen Exposure 2.2.6 Background Gas Compatibility 2.2.7 Stability 2.2.8 Maintenance 2.3 Sample System 2.4 Electronics and Signal Processing Page Page Page Installation 3.1 Unpacking the Analyzer 3.2 Mounting the Analyzer Page 3.3 Rear Panel Connections 3.3.1 Gas Connections 3.3.2 Electrical Connections 3.3.2.1 PRIMARY INPUT POWER 3.3.2.2 50-PIN EQUIPMENT INTERFACE CONNECTOR Page Page Page Page 3.4 Electrolyte Refill of BDS Sensor 3.5 Testing the System 3.6 Powering Up the System Operation 4.1 Introduction 4.2 The Analyzer application 4.3 The System Screen 4.3.1 Communication Information and Calibration Parameters 4.3.2 Setting Software Parameters: Filter, Gas Factor, Tmp. Coeff. 4.3.2.1 THE DIGITAL FILTER 4.3.2.2 The Gas Factor 4.3.2.3 T EMPERATURE C 4.3.2.4 S ET D 4.4 Calibration of the Analyzer 4.4.1 Zero Cal 4.4.1.1 Z ERO F 4.4.2 Span Cal 4.4.2.1 S PAN F 4.5 The Alarms Function Page 4.6 The Range Function 4.6.1 Setting the Analog Output Ranges Page 4.6.2 Fixed Range Analysis 4.8 Signal Output 4.9 Switching The Program Back To The Front Page Maintenance 5.1 Routine Maintenance 5.2 Adding Water to the BDS Sensor 5.3 Fuse Replacement 5.4 Battery Backup Replacement 5.5 Reinstalling Application software to PPC. 5.5 Major Internal Components 5.6 Cleaning 5.7 Troubleshooting Page Page Page Appendix A-1 Specifications Page A-2 Recommended 2-Year Spare Parts List Page A-5 Application notes Material Safety Data Sheet Teledyne Analytical Instruments 72 Section III -Physical Hazards Section IV - Health Hazard Data Oxygen Analyzer Appendix Teledyne Analytical Instruments 73 Section V - Emergency and First Aid Procedures Section VI - Handling Information Index Oxygen Analyzer Index Teledyne Analytical Instruments 75