Teledyne BDS-3960

Maintenance BDS 3960

Teledyne Analytical Instruments 54

Figure 4.3: Range Options List Box

To Set the ranges to values different than the default, click on ‘Set

Range’ and the Set Range screen will pop up.

Figure 4.4: Range Setup Screen

The first screen allows you to set range 1. If you click on the Range

button, it will take you to the setup of range 2. Click Range again will

take you to the setup of range 3, then range 4, then back again to range

1. Note that ranges and alarms are set in ppb units.

Note: The ranges must sequentially increase from low to high, for

example, if range 1 is set as 0–100 ppb and range 2 is set

Set Range 1 Limit

Upper Limit PPB

100

UP DNRANGE

OK CANCEL

Contents

Main BDS 3960 Teledyne Analytical Instruments ii Copyright 2002 Teledyne Analytical Instruments Specific Model Information Safety Messages Page Table of Contents Page Page List of Figures Page List of Tables DANGER COMBUSTIBLE GAS USAGE WARNING Introduction 1.1 Overview 1.2 Typical Applications 1.3 Main Features of the Analyzer 1.4 Front Panel (Operator Interface) Page 1.5 Rear Panel (Equipment Interface) Page Operational Theory 2.1 Introduction 2.2 BDS Sensor 2.2.1 Principles of Operation Page Page 2.2.2 Gas Flow Rate 2.2.3 Gas Pressure 2.2.4 Temperature effect 2.2.5 Recovery from High Level Oxygen Exposure 2.2.6 Background Gas Compatibility 2.2.7 Stability 2.2.8 Maintenance 2.3 Sample System 2.4 Electronics and Signal Processing Page Page Page Installation 3.1 Unpacking the Analyzer 3.2 Mounting the Analyzer Page 3.3 Rear Panel Connections 3.3.1 Gas Connections 3.3.2 Electrical Connections 3.3.2.1 PRIMARY INPUT POWER 3.3.2.2 50-PIN EQUIPMENT INTERFACE CONNECTOR Page Page Page Page 3.4 Electrolyte Refill of BDS Sensor 3.5 Testing the System 3.6 Powering Up the System Operation 4.1 Introduction 4.2 The Analyzer application 4.3 The System Screen 4.3.1 Communication Information and Calibration Parameters 4.3.2 Setting Software Parameters: Filter, Gas Factor, Tmp. Coeff. 4.3.2.1 THE DIGITAL FILTER 4.3.2.2 The Gas Factor 4.3.2.3 T EMPERATURE C 4.3.2.4 S ET D 4.4 Calibration of the Analyzer 4.4.1 Zero Cal 4.4.1.1 Z ERO F 4.4.2 Span Cal 4.4.2.1 S PAN F 4.5 The Alarms Function Page 4.6 The Range Function 4.6.1 Setting the Analog Output Ranges Page 4.6.2 Fixed Range Analysis 4.8 Signal Output 4.9 Switching The Program Back To The Front Page Maintenance 5.1 Routine Maintenance 5.2 Adding Water to the BDS Sensor 5.3 Fuse Replacement 5.4 Battery Backup Replacement 5.5 Reinstalling Application software to PPC. 5.5 Major Internal Components 5.6 Cleaning 5.7 Troubleshooting Page Page Page Appendix A-1 Specifications Page A-2 Recommended 2-Year Spare Parts List Page A-5 Application notes Material Safety Data Sheet Teledyne Analytical Instruments 72 Section III -Physical Hazards Section IV - Health Hazard Data Oxygen Analyzer Appendix Teledyne Analytical Instruments 73 Section V - Emergency and First Aid Procedures Section VI - Handling Information Index Oxygen Analyzer Index Teledyne Analytical Instruments 75