Connect Handset, Connect Power Cord | TMC ET4000 manual

Installing Your System

Step 3: Install Desk/Table Top Phones (Continued)

3 Connect Handset

Plug either end of the coiled handset cord into the handset and the other end into the jack on the side of the telephone. Place the handset in the cradle.

4 Connect Power Cord

Plug the AC power cord into the adapter jack on the bottom of the telephone. Thread the power cord into the recessed groove. Plug the AC adapter into an electrical outlet not con- trolled by a wall switch.

5 Assign a Station Number

Refer to page 8 for detailed instructions on assigning a station number.

6 Install a 9-Volt Battery (Optional)

It is not necessary for you to install a battery in your Epic telephone for it to function normally. In fact, a battery is not even needed to pre- serve your memory dial numbers in the event of a power failure. This is because all memory dial numbers are stored in a static memory which retains its contents even with no electri- cal power. The only purpose of having a bat- tery installed is so that the telephone itself can function for up to two hours in the event of a power failure. You may wish to install a battery in at least one Epic phone for emergency oper- ation, or have another standard phone avail- able. If you wish to install a battery, refer to page 68 for detailed instructions.

7 Verify Proper Installation

IMPORTANT: Please remember to perform the procedure on page 9, after you assign each station number, to verify that each telephone is properly installed.

5

Image 15

TMC ET4000 manual Connect Handset, Connect Power Cord, Assign a Station Number, Install a 9-Volt Battery Optional

Contents

User’s Guide Please read before using telephone Getting Started Important Safety Instructions Before you begin Packing List Door Intercom/Door Opener Adapter Other Optional AccessoriesMusic On Hold Adapter External Paging Adapter Table of Contents Memory Dialing Expanding the Epic System Additional InformationIndex Location of Controls LOW Battery Viii Installing Your System Identify Your Existing Wiring System If you are installing new wiring and jacks Label the jacks at each locationIf you have difficulty in identifying wall jacks Standard Installation Installing Your System Plan Your Installation Stn Installation Worksheet Installing Your System Install Desk/Table Top Phones Connect First Line CordConnect Second Line Cord Connect Handset Connect Power CordInstall a 9-Volt Battery Optional Verify Proper Installation Reverse Handset Hook Installing Your System Install Wall Mounted PhonesConnect Cords to Telephone Connect Cords to Wall Attach Telephone to Wall Using Station Names Installing Your System Verifying Proper Installation Following must be done at each station Setting Up Your System Setting Up Your System At a Glance Following must be done at Station #11 To choose which line will be automatically selected Setting Up Your System Setting Automatic Line Selection To assign distinctive rings to one or more lines Setting Up Your System Setting Distinctive Ringing Turning toll restriction on/off at a particular telephone Setting Up Your System Setting Up Toll Restriction Worksheet To set the restricted numbers at a particular telephone L1 Restricted To completely restrict specific lines at a telephone Enter To set the allowed numbers at a particular telephone To set system call privacy on/off At Station #11 Setting Up Your System Setting System Call Privacy On/Off L2 Unconnected To programPage LCD Station In-Use Indicators Operating Your System Indicator Light DescriptionLine indicators Intercom Indicator To choose how each line will ring Operating Your System Operating Your System Adjusting Volume Levels To set your system to Tone or Pulse Dialing At Station #11 Operating Your System Making a Tone/Pulse Selection To make and answer calls using the handset To make and answer calls using the speakerphoneOperating Your System Making and Answering a Call Operating Your System Using Redial To redial the last phone num- ber you dialedTo redial any of the last five phone numbers you dialed To put an outside call on hold Operating Your System Using Hold To switch between lines To make a call on another lineTo answer a call ringing on another line Operating Your System Conferencing Calls To conference two outside callsTo conference another station while on an outside call Press Transfer To send a call to Another station To use one of eight personal rings To use the transfer ring To use the NEW Call Lamp Operating Your System Using Caller IDTo see the caller ID informa- tion of an incoming call To use call waiting caller ID To dial a number in the caller list To delete numbers from the caller listEntering Area Codes into your Epic telephone To turn off the NEW Call lamp Operating Your System Using Telephone Company Voice MailTo access your voice mail mes- sages To use your NEW Call lamp to indicate voice mail messages Operating Your System Using Flash To turn mute on/off during a call Operating Your System Using Mute Operating Your System Operating Your System Using Line Reserve To cancel Line ReserveTo reserve a line that is cur- rently being used To release call privacy during a call Operating Your System Releasing Call Privacy Operating Your System Using Toll Restriction To view the length of your pre- vious five calls Operating Your System Using the Call TimerTo restart the timer from zero To view the elapsed time dur- ing your call To make and answer a call using the headset Page Directory Card Memory Dialing Memory Features Memory Dialing Using Memory Dial To store a memory dial num- berTo dial a memory dial number Memory Dialing Using Personal Directory Dial To store a personal directory dial numberTo dial a personal directory number Memory Dialing Using Shared Directory Dial To store a shared directory dial number At Station #11To dial a shared directory number Storing a dialing pause into memory Memory Dialing Special Memory FeaturesStoring a switchhook flash into memory Storing a hyphen into memory Erasing numbers stored in memory Storing one of the last five numbers dialed into memoryStoring a Caller ID number into memory Predialing To intercom another station Intercom Operation Making Intercom Calls If your phone is set to Intercom Handsfree Intercom Operation Answering Intercom CallsIf your phone is set to Intercom Ring If your phone is set to Intercom Voice Intercom Operation Making Pages To page another stationTo make an All Intercom Operation Answering Pages To answer a page directed to your station or an AllBlocking Pages at your telephone To choose how your phone will respond to intercom calls Blocking off hook voice announcements at your telephone Intercom Operation Using Off Hook Voice AnnounceTo make an off hook voice announcement To respond to an off hook voice announcement To the room you are monitoring Intercom Operation Monitoring a Room Using the Intercom Intercom Operation Naming Stations To Name a Station in Your Epic System At Station #11Guide for Entering Names Standard Configuration Expanding the Epic SystemPrivate Lines Auxiliary Lines Important Note To store a Centrex code into a memory location Centrex Operation Using Centrex With Your Epic TelephoneTo set up a private Centrex line at your telephone To assign a distinctive ring to your Centrex line To store the Centrex prefix Centrex Operation Storing the Centrex Prefix Choices are Centrex CSL OFF factory setting Centrex CSL on To set up a telephone as a Centrex console To set up a telephone to ring a Centrex console Using other Epic intercom telephones Using standard telephonesUsing fax machines and computer modems To connect a modem or a fax machine to your Epic phone Additional Information Using the Data/Fax Jack External Feature Module set as an External Paging Adapter External Feature Module set as a Music On Hold Adapter To adjust the door intercom bell volume at your telephone To answer a door speaker over the intercomTo unlock a magnetic door lock Operation During a Power Failure Additional Information Replacing Your Battery Additional Information Adjusting Held Call Reminder Additional Information Adjusting Auto Hold Drop Time Additional Information Adjusting Flash Length To erase all feature settings at a particular telephone Additional Information Erasing All Feature Settings To set your telephone’s loop voltage detector Additional Information Setting the Loop Voltage Detector Controlled by a wall switch Additional Information Troubleshooting Guide Problem Solution Additional Information FCC Information Automatic Dialers For how long after the original purchase? Additional Information Warranty InformationWhat does your warranty cover? How do you make a warranty claim? Limitations and Exclusions Dial, 32-33,46-47 Index Index LIB702YY