Toshiba 51HX94 owner manual Connecting two VCRs

Chapter 2: Connecting your TV

Connecting two VCRs

You will need:		VCR1 (plays)
￿ two coaxial cables							VIDEO		AUDIO
￿ two sets of standard A/V cables	From		IN from ANT		CH 3			L	R	IN
• For better picture performance, if VCR 1 has S-video,	antenna				CH 4
	or Cable		OUT to TV					L	R	OUT
use an S-video cable (plus the audio cables) instead of
the standard video cable. However, do not connect both
types of video cable to VIDEO 1 (or VIDEO 2) at the same time
or the picture performance will be unacceptable.			TV
• If VCR 1 has mono audio, connect L/MONO on the TV (VIDEO 1)									TheaterNet
to the audio out jack on VCR 1 using the white audio cable only.									IEEE1394	EJECT
									1
• Do not connect the same VCR to the output and input jacks on the
							AUDIO		2
							IN
TV at the same time.			VIDEO 1	VIDEO 2	COLOR	COLOR			HDMI IN
					STREAM STREAM
					HD-1	HD-2
		OUT 1	S-VIDEO	S-VIDEO			R	L
￿ To view the antenna or Cable signal:					Y	Y	2 a
									2
Turn OFF VCR 1. Select the ANT-1 video input source.*		OUT 2			PB	PB	1		1
		TheaterNet
				VIDEO	PR	PR	VIDEO
￿ To view VCR 1:
			L/	MONO	L	L	MONO
				L/			L/
					AUDIO	AUDIO				CableCARD™
				AUDIO
Turn ON VCR 1. Select the VIDEO 1 video input source.*						b	AUDIO		G-LINK
					R	R
				R			R		R
￿ To dub or edit from VCR 1 to VCR 2:				IN			OUT		DIGITAL AUDIO OUT
Turn ON both VCRs. Set VCR 2 to the appropriate line		VCR2 (records)
input (refer to your VCR ownerÕs manual for details).

ANT1
(CABLE)
ANT2
ANT (75	)

Select the VIDEO 1 video input source.*

Note:

•If you have a Cable box, connect the Cable box and splitter to VCR1 as shown on page 14.

•The VIDEO OUT signal incorporates Macrovision® copyright protection technology, which may prevent you from recording certain copy-restricted video materials.**

_____________

*To select the video input source, press INPUT on the remote control (see page 67). To program the TV remote control to operate other devices, see Chapter 3.

**This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision and is intended for home and other limited pay-per-view uses only, unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. Macrovision is a registered trademark of Macrovision Corporation.

The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs, and other materials is prohibited under the Copyright Laws of the United States and other countries, and may subject you to civil and criminal liability.

		VIDEO
IN from ANT	CH 3	L	R	IN
	CH 4
OUT to TV		L	R	OUT
		L		R

aThe VIDEO OUT jack does not output the POP picture.

bWhen the POP window is open, the AUDIO OUT jacks output the sound of the active window (main or POP). For additional information, see “Notes about recording” on page 74.

Note: The VIDEO/AUDIO OUT jacks output the signals from the ANT 1, ANT 2, VIDEO 1, VIDEO 2, or VIDEO 3 jacks when the appropriate input mode is selected.

￿To use the TV Guide On Screen recording features:

Note: If you connect your devices according to the illustration above, you will record from the TV Guide On Screen system to the VCR labeled “VCR2.”

1.Connect the G-LINK cable according to the instructions on page 25.

2.Make sure the VCR2 is connected to the A/V OUT jacks on the TV (see illustration).

3.Set the VCR to the appropriate line input (refer to your VCR ownerÕs manual for details), and then turn OFF the VCR.

4.See Chapter 5 for details on setting up the TV Guide On Screen system.

5.See Chapter 7 for details on using the TV Guide On Screen system.

18 Copyright © 2004 TOSHIBA CORPORATION. All rights reserved.

51,57HX94(E)012-25 18 9/12/04, 7:01 PM