Chapter 2: Connecting your TV

G-LINKconnection

This connection is necessary for the TV Guide On Screen™ system to work with your cable box to receive program listings and to enable TV Guide On Screen recording features with your VCR.

Note: This connection is not necessary for A/V HD or D-VHS recording devices. See pages 23 and 50 for further details.

After you connect your devices to the TV, you will need to connect the G-LINK cable (either of the dual-wand IR blaster cables included with your TV) from your VCR and Cable box (if applicable) to the G-LINK jack on the TV.

Note: TV Guide On Screen program data is available through the ANT-1 and ANT-2 antenna inputs and also through the VIDEO 1 inputs if you have a cable box connected to VIDEO 1. TV Guide On Screen program data is not available through any other inputs on this TV. See the connection information on pages 13–18.

The G-LINK connection is necessary to enable the following features of your TV Guide On Screenª system:

¥If you have a Cable box, you need to connect the G-LINK cable from the Cable box to the G-LINK jack to receive the TV Guide On Screen systemÕs program listings for your Cable service.

¥If you have a VCR, you need to connect the G-LINK cable from the VCR to the G-LINK jack to use the TV Guide On Screen systemÕs recording features.

To connect to the G-LINK jack:

1.Locate the infrared sensor on the front of your VCR or Cable box. The sensor is marked on some devices.*

2.Align one of the G-LINK (IR blaster) cableÕs wands about 1 inch away from the infrared sensor on the front of the VCR and attach it using double-sided mounting tape.

If you have a Cable box, attach the other wand in a similar manner. (See illustration at right.)

Front of Cable box

Front of VCR

Note: If you do not have a Cable box, coil the second wand with a rubber band and leave it behind the TV.

3.Plug the G-LINK (IR blaster) cableÕs plug into the TVÕs G-LINK jack.

For details on setting up the TV Guide On Screen system:

See Chapter 5.

For details on using the TV Guide On Screen interactive program guide:

Infrared sensor

G-LINK (IR blaster) cable wand (approx. 1 inch from device)

Back of TV

TheaterNet

IEEE1394

EJECT

1

ANT1

(CABLE)

See Chapter 7.

*If you cannot locate the device’s infrared sensor: 1. Turn OFF the device.

2.Starting at the lower left corner of the device, place the end of the device’s remote control (with the infrared emitter) so it touches the front of the device and press POWER. (Do not use the TV’s remote control for this step.)

3.If the device turns on, the place the remote control touched the device is the location of the sensor.

4.If the device does not turn on, move the remote control slightly to the right and press POWER again.

5.Repeat step 4 until you locate the device’s infrared sensor.

OUT 1

OUT 2

TheaterNet

 

 

 

 

IN

 

 

 

 

 

AUDIO

 

VIDEO 1

VIDEO 2

COLOR

COLOR

 

 

STREAM

STREAM

 

 

 

 

HD-1

HD-2

 

 

S-VIDEO

S-VIDEO

 

 

R

L

 

 

 

 

 

 

Y

Y

2

 

 

 

PB

PB

1

 

VIDEO

VIDEO

PR

PR

VIDEO

VAR

 

 

 

AUDIO

 

 

 

 

L/

L/

L/

 

 

 

MONO

MONO

L

L

MONO

L

AUDIO

AUDIO

AUDIO

AUDIO

AUDIO

 

 

 

 

R

R

R

R

R

R

 

 

 

IN

 

OUT

 

2

HDMI IN

2

1

CableCARD™

G-LINK

DIGITAL AUDIO OUT

ANT2

ANT (75 )

Copyright © 2004 TOSHIBA CORPORATION. All rights reserved.

25

 

51,57HX94(E)012-25

25

9/12/04, 7:03 PM

Page 25
Image 25
Toshiba 51HX94 owner manual LINKconnection, To connect to the G-LINK jack, See Chapter