Toshiba TDP-TW420 owner manual Setting up the Network Projector/Network Utility

Using the menus 2

N Setup using the Setting display (2)

L Projector settings (Be sure to read this subsection.)

Using the factory settings as-is may suffer security damage, so be sure to change the projector settings.

1. Press the NETWORK button and press the MENU button twice

N Setting up the Network Projector/Network Utility

If you select Network Utility, the following items can be set.

Category	Item				Description
Wireless	Easy Connect	[Yes	No]	[Enter:	]
LAN	(USB memory)
	LAN settings		Mode: Ad hoc		Infrastructure
			SSID: Specify a desired character string (1 to 32 characters).

2. Select a Category

Select a category by using .

The following 5 categories are available:

Network Projector p.49

setup
Network utility	p.49
setup
Control setting	p.55
Slideshow setup	p.56
Status display	p.58

3. Make settings Press

Item

The Setting display (2) is displayed.

* Appears only when Network or USB memory input is selected.

Displays the current settings of selected category.

Item shown in gray cannot be set with the currently set conditions of the projector.

or to open the menu.

These marks signify the items can be

selected from the list by using . After an item is selected, apply it by

pressing .

		[		: Move left or right one character.]				[	to	: Set a character.]
		DHCP: Use			Not use
		IP address: Enter using the numeric keys of the remote control.
		[		: Move left or right one character.]				[	to	: Set a character.]
		Subnet mask: Enter using the numeric keys of the remote control.
		[		: Move left or right one character.]				[	to	: Set a character.]
		Gateway: Enter using the numeric keys of the remote control.
		[		: Move left or right one character.]				[	to	: Set a character.]
		Confirm: [OK]			[Cancel]		[Enter:	]
	Security	Network authentication: Network Authentication Setting
		[	or	: Enter setting]		[	: Selection]			[Enter: ]
		None/Open/Shared/WPA-PSK/WPA2-PSK
		Encryption: Select an encryption type using the								button.
		Off/WEP/TKIP/AES
		Key index: Select a desired number (1 to 4) using the								buttons.
		Network key: Specify a desired character string.
		(WEP: 5 to 13 characters, or 10 to 26 digits in hexadecimal notation)
		(TKIP/AES: 8 to 63 characters, or 64 digits in hexadecimal notation)
		[		: Move left or right one character.]				[	to	: Set a character.]
		Confirm: [OK]			[Cancel]		[Enter:	]
	Setting	Reset all the wireless LAN settings.
	Iinitialization	Confirm: [Yes]			[No]	[Enter: ]
Wired	LAN settings	DHCP: Use			Not use
LAN		IP address: Enter using the numeric keys of the remote control.
		[		: Move left or right one character.]				[	to	: Set a character.]
		Subnet mask: Enter using the numeric keys of the remote control.
		[		: Move left or right one character.]				[	to	: Set a character.]
		Gateway: Enter using the numeric keys of the remote control.
		[		: Move left or right one character.]				[	to	: Set a character.]

Network and USB memory

The figure shows a typical example. As the display may differ depending on the item, use the following pages as a reference.

While the video file transfer function of Network Utility or the slideshow function is in use, the background image of the Setting display (2) does not appear.

4. Back	RETURN button
5. End	Press the MENU button or RETURN button.
	(The menu disappears 30 seconds after the last operation is conducted.)

Confirm: [OK] [Cancel] [Enter: ]

* To enter characters, use the numeric keypad on the remote control.

48 49