Trango Broadband M900S user manual Appendix a Command Set Reference, Command Radio Description

Appendix A		Command Set Reference
	(ro = read only access, rw = read write access)
Command			Radio	Description	Access
?			AP/SU	Display complete list of commands and syntax	ro/rw
? <command>			AP/SU	Display specific command syntax	ro/rw
antenna			AP/SU	Display current antenna setting	ro/rw
				(h=horizontal, v=vertical, e=external )
antenna <e h v>			AP/SU	Select antenna mode	rw
				(h=horizontal, v=vertical, e=external) Note: Only use ‘e’ on
				M900S-SU-EXT
aprssi <ch#> <antenna, h v e>			AP/SU	Scan two strongest APs	ro/rw
				(Opmode “OFF” only)
apsearch			AP/SU	Scan all channels to look for APs	ro/rw
				(Opmode “OFF” only)
arq			AP/SU	Display current ARQ settings	ro/rw
arq <onoff>			AP/SU	Enable/disable ARQ	rw
bye			AP/SU	Same as “logout”	ro/rw
eth link			AP/SU	Display current Ethernet setting	ro/rw
eth link <100fdx100hdx10fdx10hdxaneg>			AP/SU	Change Ethernet duplex setting	rw
exit			AP/SU	Same as “logout”	ro/rw
freq			AP/SU	Display current channel	ro/rw
freq <ch#>			AP/SU	Change current channel	rw
freq channeltable			AP/SU	Display channel table	ro/rw
freq writechannel [<ch #> <freq>]…			AP/SU	Modify center frequency of channel.	rw
				<ch #> = 1..4
				<freq> = 906..924
				Note: This command automatically writes to flash memory.
help			AP/SU	Display complete list of commands and syntax	ro/rw
help <command>			AP/SU	Display specific command syntax	ro/rw
ipconfig [<new ip> <new subnet mask> <new			AP/SU	Assign radio’s IP, subnet mask, and gateway IP	rw
gateway>]
linktest <txrxrxtx> [<pkt len, bytes> [<# of			AP/SU	Loopback test to check quality of the wireless link. Variable	ro/rw
pkts> [<# of cycle>]]]				parameters include:
				pktlen = 64..1760,
				# 0 pkts = 1..500
				# of cycles = 1..100000
logout			AP/SU	Log out of radio	ro/rw
maclist			AP/SU	Display current MAC table (MAC addresses of attached devices)	ro/rw
maclist reset			AP/SU	Display or reset current MAC table	ro/rw
mirth			AP	Display MIR (Maximum Information Rate) Threshold	ro/rw
mirth <0..3, Mbps>			AP	Assign MIR Threshold	rw
				default = 3 Mbps
				mirth 0 = Always On
				mirth 3 = Disable MIR Threshold
opmode			AP/SU	Display current Opmode	ro/rw
opmode on [<y>]			AP/SU	Set Opmode to be “ON” and use “y” if Opmode is not as same as	ro/rw
				default Opmode
password <rwro> <new pwd> <new pwd>			AP/SU	Specify new password (max 15 octs)	rw
				rw=read/write password, ro=read only password
ping <ip address>			AP/SU	Ping local Ethernet device	ro/rw
				Note: This command only works for local Ethernet devices, not SU
				or any device behind SU.
power			AP/SU	Display current TX power level	ro/rw
				default = max. power value
power set <minmax<dBm>			AP/SU	Specify TX power for both band	rw
				Note: SU’s power will be adjusted by AP during association process
	Trango Broadband Wireless — User Manual M900S Rev. C				Page 43