Trango Broadband M900S user manual Su ipconfig suid new IP new

Command		Radio	Description		Access
			21.	TX power
			22.	Remarks
			23. RF TX retry at AP, RF TX retry maxed out at AP
			RF TX retry at SU, RF TX retry maxed out at SU
su ipconfig <suid> <new IP> <new		AP	Change IP, subnet, gateway for specified SU		rw
subnet> <new gateway>
su linktest <suid>		AP	Perform linktest for specified SU		ro/rw
su ping <suid>		AP	Request SU’s ranging and RSSI information		ro/rw
su reboot <all suid>		AP	Reboot a specific SU or all SUs		rw
su sw <suid> <sw #> <on off>		AP	Change switch settings on specified SU		rw
sudb add <suid> <prre> <mac>		AP	Add new SU to SUDB		rw
sudb cirmir <<suid>all> <cir dn> <cir up>		AP	Change SU’s CIR/MIR settings		rw
<mir dn> <mir up>
sudb defaultcirmir		AP	Display default CIR and MIR in SUDB		ro/rw
sudb defaultcirmir <cir_dn, 0..3000> <cir_up,		AP	Change default CIR and MIR		rw
0..3000> <mir_dn, 0..3000> <mir_up, 0..3000>
sudb defaultcirmir <default cir dn> <default cir		AP	Set MIR/CIR values to default values		rw
up> <default mir dn> <default mir up>
sudb delete <suid all>		AP	Delete SU in SUDB		rw
sudb dload		AP	Download SUDB file from TFTP buffer and write to flash memory.		rw
			This command is used to load a text file that contains the SUDB into
			the AP. This command can be useful if there are large numbers of
			SUs in the sector.
sudb gid <suid all> <0..15>		AP	Change SU’s gid		rw
sudb view		AP	Display all SUDB		ro/rw
survey <search time, sec> <antenna, h v e>		AP/SU	Spectrum analysis of the entire band (and near band)		ro/rw
			<search time> = 1..10 sec per channel
			Opmode “OFF” only
Sw		AP/SU	Display current sw setting		ro/rw
sw 0 [<on off>]		AP/SU	set sw #0 – enable or disable packet filter for broadcast/ multicast		rw
			packets
			on = filtering
			default = on
sw 1 [<on off>]		SU	Enable or disable SU’s autoscan AP feature		rw
			If on, SU will automatically scan each channel and antenna port
			searching for AP.
			default=on
			Note: Recommended setting for M900S-SU-EXT is off.
sw 2 [<on off>]		SU	Enable or disable SU’s TCP/IP service for AP		rw
			Allows TCP/IP access to SU from AP side of network via wireless
			link.
			default = on
sw 3 [<on off>]		AP	Enable or disable SU to SU (peer to peer) service		rw
			default = off
sw 5 [<on off>]		AP/SU	Enable or disable HTTPD (browser interface)		rw
			default = on
sw 6 [<on off>]		SU	Enable or disable TCP/IP service for Ethernet port while SU is in		rw
			Opmode “ON”
			default = on
sw 7 [<on off>]		AP	Enable or disable TCP/IP service for SU. Allows TCP/IP access to		rw
			AP from SU side of network via wireless link.
			default = on
sysinfo		AP/SU	Display system configuration		ro/rw
targetap		SU	Display the SU current setting for target AP		ro/rw
targetap all		SU	SU will associate with any AP with the same Base ID		rw
			“all” is the default setting.
targetap only <mac1, hex> [<mac2, hex>]		SU	SU will only associate with AP with specified MAC addresses.		rw
targetrssi		AP	Display SU Target RSSI in dBm. This setting is used in the SU		ro/rw
			power leveling process.
	Trango Broadband Wireless — User Manual M900S Rev. C				Page 45