Parallel Port IRQ, OnboardIDE | Tyan Computer InterServe 90 guide

newer devices; consult your device’s user information for the appropriate port type. There are no default settings.

Parallel Port IRQ

This option specifies the IRQ used by the parallel port, and only appears if OnBoard Parallel Port is set to 278 or 378. The settings are 5 or 7.

Parallel Port DMA Channel

This option is only available if the setting for the Parallel Port Mode option is set to ECP and the OnBoard Parallel Port option is set to 378, 278, or 3BC. This option sets the DMA channel used by the parallel port. The settings are 0 through 7 in increments of one.

OnboardIDE

This option specifies the IDE channel used by the onboard IDE controller. The settings are Disabled, Primary, Secondary, or Both.

BIOS

http://www.tyan.com

67

Image 69

Tyan Computer InterServe 90 manual Parallel Port IRQ, Parallel Port DMA Channel, OnboardIDE

Contents

InterServe Errata Pins Tyan S1832DL Tiger Table of Contents Appendix 1 CPU Retention Module Options Appendix 2 Glossary System Resources Overview Chapter Icons Hardware Specifications/Features Physical Dimensions Bios InformationDisk Drive & System I/O Technical Support Software SpecificationsAlt.comp.periphs.mainboard.tyan 510 For Resellers Only Returning Merchandise for Service Unpacking Installation What’s the first thing I should do? Install the motherboard into your case Conforms to industry standard revision Plug in the power connector as shown Pin Chapter Next are the Com and Printer ports Connecting the USB and PS/2 ports Shows the USB ports and the PS/2 ports Installing your add-in cards is relatively simple but Next, you need to install your memory Install Finally, install your CPU Installing CPU Retention Modules Installing the Active ProcessorActive Passive Chapter Installing the Passive Processor Removing the CPU Setting JumpersYou are done Pin jumpers Or more pin jumpers Off Open This page has been intentionally left blank Quick References for Jumpers Onboard Resource Settings Map of Motherboard Jumpers PS/2 ports COM2 LPT1 COM1 USB ports LM79 PCI slots CPU Settings for 100MHz Bus CPU Settings for 66MHz Bus J10 External Pin Assignments 2x9 External Connector Proprietary Server Mgmt Connector Soft Power Connector Speaker Connector InstallationHardware Reset Switch Connector Installation Chassis Intrusion Alarm Connector Flash EepromWindows 95 Users RAM Installation Hardware Cmos & Password Reset Dimm Cache Memory Pin Dimm Frequently Asked Questions Chapter This page has been intentionally left blank Bios Configuration Key Function Main Setup Floppy Drive a and B System Date/Time Type How to Configure Parameter Description Entering Drive Parameters Optimal Defaults Boot Sector Virus ProtectionFail-Safe Defaults Auto-Detect Hard Disks Advanced Cmos Setup Default Settings Chart Advanced Cmos Setup Quick Boot Settings Chart 2nd Boot Device 1st Boot Device3rd Boot Device Try Other Boot Devices Password Check Boot Up Num-LockBoot To OS/2 System Bios Cacheable Cache Bus ECC Default Primary VideoMPS Revision C000,16K Shadow and C400,16K Shadow Advanced Chipset Setup Enter Chipset Setup AGP S E R R USB Function Multi-Trans Timer Clks BX Master Latency Timer ClksUSB KB/Mouse Legacy Support Port 64/60 Emulation Dram Integrity Mode PCI1 to PCI0 AccessSetting Description Sdram RAS# to CAS# Delay AGP Low-Priority Timer Clks AGP Multi-Trans Timer AGP ClksAGP Parity Error Response 8bit I/O Recovery Time USB Passive Release 16bit I/O Recovery TimePIIX4 Passive Release TypeF DMA Buffer Control1 Power Management Setup Enter Power Management Setup Power Button Function Power Management/APMGreen PC Monitor Power State Acpi Aware O/S Hard Disk Power Down Mode Video Power Down ModePower Saving Type Standby/Suspend Timer Unit Slow Clock Ratio PC98 Power LEDDisplay Activity LAN Wake-up RTC Wake-up Plug and Play Setup Plug and Play Setup Default Settings Chart Plug and Play Aware O/S PCI Latency Timer PCI ClocksPCI VGA Palette Snoop Allocate IRQ to PCI VGA Offboard PCI IDE Secondary IRQ OffBoard PCI IDE Primary IRQPCI Slot n IRQ Priority DMA Channel n Bios Devnode for Shadow RAM Reserved Memory AddressPCI Device Search Order Peripheral Setup Default Settings Chart Peripheral Setup Power Interruption Default Settings ChartSerial Port2 Mode Overclock Warning Message Mode Description IR Transmission ModeParallel Port Mode IR Receiver Pin Parallel Port IRQ Parallel Port DMA ChannelOnboardIDE Supervisor and User Security Flash Writer Utility Language Utility Beep Codes System Resources If the computer beeps Then Troubleshooting System Problems Error Message Explanation Displayed Error Messages OFF Board Parity Error Addr = Error Message Explanation Appendix Option Glossary Page Appendix Page Appendix Page Appendix Document # D1308-210