Default Settings Chart, LM79 INX | Tyan Computer InterServe 90

Default Settings Chart (Continued)

Setting Option	Optimal Default	Fail-Safe Default
*IR R eceiver P in	IR R X1	IR R X1
OnboardP arallel P ort	378	378
P arallel P ort Mode	Normal	Normal
*EP P Vers ion	N/A	N/A
P arallel P ort IR Q	7	7
*P arallel P ort DMA Channel	N/A	N/A
OnboardIDE	B oth	B oth

* Setting Option is not Selectable

Overclock Warning Message

When enabled, this option sends a warning message if the CPU is overclocked. The settings are Enabled or Disabled.

LM79 IN(X)

This option specifies various CPU core voltage settings.

Power Interruption

The settings are Enabled or Disabled.

Onboard FDC

Set this option to Enabled to enable the floppy drive controller on the mother- board. The settings are Auto, Enabled, or Disabled.

Onboard Serial Port1

This option specifies the base I/O port address of serial port 1. The settings are Auto, Disabled, 3F8h, 2F8h, 3E8h, or 2E8h.

Onboard Serial Port2

This option specifies the base I/O port address of serial port 2. The settings are Auto, Disabled, 3F8h, 2F8h, 3E8h, or 2E8h.

Serial Port2 Mode

This option specifies the operating mode for serial port 2. This option will not appear if the Onboard Serial Port2 option is set to Disabled, or is set to Auto and your system does not have an onboard serial port 2. The settings are Normal, Sharp-IR, IrDA, and Consumer.

http://www.tyan.com

BIOS

65

Image 67

Tyan Computer InterServe 90 Default Settings Chart, Overclock Warning Message, LM79 INX, Power Interruption, Onboard FDC

Contents

InterServe Errata Pins Tyan S1832DL Tiger Table of Contents Appendix 1 CPU Retention Module Options Appendix 2 Glossary System Resources Overview Chapter Icons Hardware Specifications/Features Bios Information Physical DimensionsDisk Drive & System I/O 510 Software SpecificationsTechnical Support Alt.comp.periphs.mainboard.tyan For Resellers Only Returning Merchandise for Service Unpacking Installation What’s the first thing I should do? Install the motherboard into your case Conforms to industry standard revision Plug in the power connector as shown Pin Chapter Next are the Com and Printer ports Connecting the USB and PS/2 ports Shows the USB ports and the PS/2 ports Installing your add-in cards is relatively simple but Next, you need to install your memory Install Finally, install your CPU Installing the Active Processor Installing CPU Retention ModulesActive Passive Chapter Installing the Passive Processor Pin jumpers Or more pin jumpers Off Open Setting JumpersRemoving the CPU You are done This page has been intentionally left blank Quick References for Jumpers Onboard Resource Settings Map of Motherboard Jumpers PS/2 ports COM2 LPT1 COM1 USB ports LM79 PCI slots CPU Settings for 100MHz Bus CPU Settings for 66MHz Bus J10 External Pin Assignments 2x9 External Connector Proprietary Server Mgmt Connector Speaker Connector Installation Soft Power ConnectorHardware Reset Switch Connector Installation Flash Eeprom Chassis Intrusion Alarm ConnectorWindows 95 Users RAM Installation Hardware Cmos & Password Reset Dimm Cache Memory Pin Dimm Frequently Asked Questions Chapter This page has been intentionally left blank Bios Configuration Key Function Main Setup Floppy Drive a and B System Date/Time Type How to Configure Parameter Description Entering Drive Parameters Auto-Detect Hard Disks Boot Sector Virus ProtectionOptimal Defaults Fail-Safe Defaults Advanced Cmos Setup Default Settings Chart Advanced Cmos Setup Quick Boot Settings Chart Try Other Boot Devices 1st Boot Device2nd Boot Device 3rd Boot Device System Bios Cacheable Boot Up Num-LockPassword Check Boot To OS/2 C000,16K Shadow and C400,16K Shadow Default Primary VideoCache Bus ECC MPS Revision Advanced Chipset Setup Enter Chipset Setup AGP S E R R USB Function Port 64/60 Emulation BX Master Latency Timer ClksMulti-Trans Timer Clks USB KB/Mouse Legacy Support Sdram RAS# to CAS# Delay PCI1 to PCI0 AccessDram Integrity Mode Setting Description 8bit I/O Recovery Time AGP Multi-Trans Timer AGP ClksAGP Low-Priority Timer Clks AGP Parity Error Response TypeF DMA Buffer Control1 16bit I/O Recovery TimeUSB Passive Release PIIX4 Passive Release Power Management Setup Enter Power Management Setup Acpi Aware O/S Power Management/APMPower Button Function Green PC Monitor Power State Standby/Suspend Timer Unit Video Power Down ModeHard Disk Power Down Mode Power Saving Type LAN Wake-up PC98 Power LEDSlow Clock Ratio Display Activity RTC Wake-up Plug and Play Setup Plug and Play Setup Default Settings Chart Allocate IRQ to PCI VGA PCI Latency Timer PCI ClocksPlug and Play Aware O/S PCI VGA Palette Snoop DMA Channel n OffBoard PCI IDE Primary IRQOffboard PCI IDE Secondary IRQ PCI Slot n IRQ Priority Reserved Memory Address Bios Devnode for Shadow RAMPCI Device Search Order Peripheral Setup Default Settings Chart Peripheral Setup Overclock Warning Message Default Settings ChartPower Interruption Serial Port2 Mode IR Receiver Pin IR Transmission ModeMode Description Parallel Port Mode Parallel Port DMA Channel Parallel Port IRQOnboardIDE Supervisor and User Security Flash Writer Utility Language Utility Beep Codes System Resources If the computer beeps Then Troubleshooting System Problems Error Message Explanation Displayed Error Messages OFF Board Parity Error Addr = Error Message Explanation Appendix Option Glossary Page Appendix Page Appendix Page Appendix Document # D1308-210