Reserved Memory Address | Tyan Computer InterServe 90 manual

Reserved Memory Address

This option specifies the beginning address (in hex) of the reserved memory area. The specified ROM memory area is reserved for use by legacy ISA adapter cards. This option does not appear if the Reserved Memory Size option is set to Disabled. The settings are C0000, C4000, C8000, CC000, D0000, D4000, D8000, or DC000.

PCI Device Search Order

This option changes the BIOS scan order of the PCI slot - from first to last or last to first. The settings are First-Last or Last-First.

BIOS Devnode for Shadow RAM

This option is used for some add-on card ROMs which do not claim the correct memory range that they occupy. The settings are Disabled or Enabled.

BIOS

http://www.tyan.com

63

Image 65

Tyan Computer InterServe 90 manual Reserved Memory Address, PCI Device Search Order, Bios Devnode for Shadow RAM

Contents

InterServe Errata Pins Tyan S1832DL Tiger Table of Contents Appendix 1 CPU Retention Module Options Appendix 2 Glossary System Resources Overview Chapter Icons Hardware Specifications/Features Disk Drive & System I/O Physical DimensionsBios Information Technical Support Software SpecificationsAlt.comp.periphs.mainboard.tyan 510 For Resellers Only Returning Merchandise for Service Unpacking Installation What’s the first thing I should do? Install the motherboard into your case Conforms to industry standard revision Plug in the power connector as shown Pin Chapter Next are the Com and Printer ports Connecting the USB and PS/2 ports Shows the USB ports and the PS/2 ports Installing your add-in cards is relatively simple but Next, you need to install your memory Install Finally, install your CPU Active Passive Installing CPU Retention ModulesInstalling the Active Processor Chapter Installing the Passive Processor Removing the CPU Setting JumpersYou are done Pin jumpers Or more pin jumpers Off Open This page has been intentionally left blank Quick References for Jumpers Onboard Resource Settings Map of Motherboard Jumpers PS/2 ports COM2 LPT1 COM1 USB ports LM79 PCI slots CPU Settings for 100MHz Bus CPU Settings for 66MHz Bus J10 External Pin Assignments 2x9 External Connector Proprietary Server Mgmt Connector Hardware Reset Switch Connector Installation Soft Power ConnectorSpeaker Connector Installation Windows 95 Users Chassis Intrusion Alarm ConnectorFlash Eeprom RAM Installation Hardware Cmos & Password Reset Dimm Cache Memory Pin Dimm Frequently Asked Questions Chapter This page has been intentionally left blank Bios Configuration Key Function Main Setup Floppy Drive a and B System Date/Time Type How to Configure Parameter Description Entering Drive Parameters Optimal Defaults Boot Sector Virus ProtectionFail-Safe Defaults Auto-Detect Hard Disks Advanced Cmos Setup Default Settings Chart Advanced Cmos Setup Quick Boot Settings Chart 2nd Boot Device 1st Boot Device3rd Boot Device Try Other Boot Devices Password Check Boot Up Num-LockBoot To OS/2 System Bios Cacheable Cache Bus ECC Default Primary VideoMPS Revision C000,16K Shadow and C400,16K Shadow Advanced Chipset Setup Enter Chipset Setup AGP S E R R USB Function Multi-Trans Timer Clks BX Master Latency Timer ClksUSB KB/Mouse Legacy Support Port 64/60 Emulation Dram Integrity Mode PCI1 to PCI0 AccessSetting Description Sdram RAS# to CAS# Delay AGP Low-Priority Timer Clks AGP Multi-Trans Timer AGP ClksAGP Parity Error Response 8bit I/O Recovery Time USB Passive Release 16bit I/O Recovery TimePIIX4 Passive Release TypeF DMA Buffer Control1 Power Management Setup Enter Power Management Setup Power Button Function Power Management/APMGreen PC Monitor Power State Acpi Aware O/S Hard Disk Power Down Mode Video Power Down ModePower Saving Type Standby/Suspend Timer Unit Slow Clock Ratio PC98 Power LEDDisplay Activity LAN Wake-up RTC Wake-up Plug and Play Setup Plug and Play Setup Default Settings Chart Plug and Play Aware O/S PCI Latency Timer PCI ClocksPCI VGA Palette Snoop Allocate IRQ to PCI VGA Offboard PCI IDE Secondary IRQ OffBoard PCI IDE Primary IRQPCI Slot n IRQ Priority DMA Channel n PCI Device Search Order Bios Devnode for Shadow RAMReserved Memory Address Peripheral Setup Default Settings Chart Peripheral Setup Power Interruption Default Settings ChartSerial Port2 Mode Overclock Warning Message Mode Description IR Transmission ModeParallel Port Mode IR Receiver Pin OnboardIDE Parallel Port IRQParallel Port DMA Channel Supervisor and User Security Flash Writer Utility Language Utility Beep Codes System Resources If the computer beeps Then Troubleshooting System Problems Error Message Explanation Displayed Error Messages OFF Board Parity Error Addr = Error Message Explanation Appendix Option Glossary Page Appendix Page Appendix Page Appendix Document # D1308-210