Tyan Computer InterServe 90 Displayed Error Messages

http://www.tyan.com

72

egasseMrorrEnoitanalpxE

rorrE02A-etaG2408 .2408ehtecalpeR.gnikrowtonsi)2408(rellortnocdraobyekehtno02AetaG

!trohSeniLsserddA.yrtiucricgnidocedsserddaehtnirorrE

rorrEevirD:C drah:CehtkcehC.ytilitUksiDdraHgaiDIMAehtnuR.:CevirdmorfesnopseroN .puteSdradnatSniepytksid

eruliaFevirD:C.evirdehtecalpeR.:CevirdksiddrahmorfesnopseroN

,daByromeMehcaC !ehcaCelbanEtoNoD .gaiDIMAnuR.evitcefedsiyromemehcaC

rorrEremiT2-HC.2remitnirorrenasierehT.sremitowtsahmetsysTAnA

etatSyrettaBSOMC woL ehtecalpeR.wolsirewopyrettabehT.yrettabaybderewopsiMARSOMC .yrettab

muskcehCSOMC eruliaF .puteSSOIBNIWnuR.eulavsuoiverpehtnahttnereffidsimuskcehcMARSOMC

metsySSOMC teStoNsnoitpO .puteSSOIBNIWnuR.deyortsedneebevahMARSOMCniderotsseulavehT

epyTyalpsiDSOMC hctamsiM SOIBNIWnuR.detcetedepytehthctamtonseodMARSOMCniepytoedivehT .puteS

eziSyromeMSOMC hctamsiM SOMCnitnuomaehtnahttnereffidsiSOIBIMAybdnuofyromemfotnuomaehT .puteSSOIBNIWnuR.MAR

etaDdnaemiTSOMC teStoN .emitdnaetadehttesotputeSdradnatSnuR

rorrEevirD:D drahehtkcehC.ytilitUksiDdraHgaiDIMAehtnuR.:DevirdmorfesnopseroN .puteSdradnatSniepytksid

Displayed Error Messages

If an error occurs after the system display has been initialized, the error

message will be displayed as follows:

ERROR Message Line 1

ERROR Message Line 2

Press <F1> to continue

and the system will halt. The system will not halt if the Wait for <F1> If Any

Error option in Advanced Setup is Disabled.

RUN SETUP UTILITY

may also appear. Press <F1> to run WINBIOS Setup if this message appears.

Chapter 5

System Resources

Contents

Main Page Tyan S1832DL Tiger 100 Motherboard Users Manual Revision 2.10 PRINTED IN USA. Table of Contents Page Overview chapter 1 Introduction Icons Hardware Specifications/Features Processor Information Chipset Information Voltage and Power Information Main Memory Up to 1024MB onboard. Physical Dimensions BIOS Information Disk Drive & System I/O Software Specifications OS Technical Support Returning Merchandise for Service For Resellers Only: chapter 2 Board Installation Unpacking Installation How to install our products right...the first time. Install the motherboard into your case. Plug in the power connector as shown. Next, connect your IDE cables (if youre using IDE hard drives). Pin 1 Now that you have installed your IDE drives, your floppies are next. Next are the Com and Printer ports. Warning: Connecting the USB and PS/2 ports. Installing your add-in cards is relatively simple but... Next, you need to install your memory. T Finally, install your CPU. Installing CPU Retention Modules key pin on the Installing the Active Processor Page Installing the Passive Processor Removing the CPU. You are done. Setting Jumpers Page Quick References for Jumpers chapter 3 Onboard Resource Settings The tiny 1s next to jumpers of 3 pins or more indicate the position of pin 1 for that jumper. Map of Motherboard Jumpers B Page CPU Settings for 66MHz Bus tluM zHM004 tluM CMOS Reset http://www.tyan.com InfraRed/Floppy Drive Settings J10 External Pin Assignments JP20 Pinout JP21 Pinout Other Pin Assignments 2x9 External Connector Proprietary Server Mgmt Connector sniP2-101-661-3102-8132-2272-42 noitcnuF Soft Power Connector Speaker Connector Installation Hardware Reset Switch Connector Installation Chassis Intrusion Alarm Connector Windows 95 Users: CMOS RTC Flash EEPROM Hardware CMOS & Password Reset RAM Installation NOTE: Table below shows only some of the possible memory configurations. Cache Memory Frequently Asked Questions Page Page chapter 4 BIOS Configuration The AMIBIOS Setup screen is shown below. 3.1 Main Setup Page Page Page Default Settings 3.2 Advanced CMOS Setup Advanced CMOS Setup Default Settings Chart Settings Chart (Continued) Advanced Setup gnitteSnoitpircseD Page Page Page 3.3 Chipset Setup Advanced Chipset Setup Default Settings Chart Setting Option Optimal Default Fail-Safe Default Settings Chart (continued) Page Page Page Page 3.4 Power Management Setup Power Management Setup Default Settings Chart Setting Option Optimal Default Fail-Safe Default Page Page Page 3.5 Plug and Play Setup Plug and Play Setup Default Settings Chart * Setting option is not selectable Page Page Page 3.6 Peripheral Setup Peripheral Setup Default Settings Chart Page edoMnoitpircseD Page 3.7 Supervisor and User Security 3.8 Language Utility 3.9 Flash Writer Utility chapter 5 System Resources Beep Codes SYSTEM Troubleshooting System Problems If the computer beeps... then... Displayed Error Messages egasseMrorrEnoitanalpxE SYSTEM Appendix 1 CPU Retention Module Options Page Appendix 2 Glossary Page Page Page Page Page Page Notice for the USA Document # D1308-210 CAUTION: LITHIUM BATTERIES included with This PC board. Notice for Canada Notice for Europe (CE Mark)