USB KB/Mouse Legacy Support | Tyan Computer InterServe 90 specs

USB KB/Mouse Legacy Support

Set this option to Enabled to enable support for older keyboards and mouse devices if the USB Function option is set to Enabled. The settings are Enabled or Disabled.

Port 64/60 Emulation

Setting this option to Enabled allows a USB keyboard to act like a legacy keyboard. If this option is not Enabled, USB keyboard lights will not work under Windows NT. With other operating systems, a USB keyboard will work normally with this option Disabled. The settings are Enabled or Disabled.

SERR#

Set this option to Enabled to enable the SERR# signal on the bus. The settings are Enabled or Disabled.

PERR#

Set this option to Enabled to enable the PERR# signal on the bus. The settings are Enabled or Disabled. The Optimal and Fail-safe default settings are Disabled.

WSC# Handshake

Set this option to Enabled to enable handshaking for the WSC# signal. Handshaking is a form of encryption; see the Glossary for more information. The settings are Enabled or Disabled.

USWC Write Post

This option sets the status of USWC posted writes to I/O. USWC is a type of memory that is used by VGA devices. The settings are:

Setting	Description

Enabled	USWC posted writes to I/O are enabled.

Disabled	USWC posted writes to I/O are disabled.

BX Master Latency Timer (Clks)

This option specifies the master latency timer (in PCI clocks) for devices in the computer. The settings are Disabled, 32, 64, 96, 128, 160, 192, or 224.

Multi-Trans Timer (Clks)

This option specifies the multi-trans latency timings (in PCI clocks) for devices in the computer. The settings are Disabled, 32, 64, 96, 128, 160, 192, or 224.

http://www.tyan.com

BIOS

51

Image 53

Tyan Computer InterServe 90 manual USB KB/Mouse Legacy Support, Port 64/60 Emulation, WSC# Handshake, Uswc Write Post

Contents

InterServe Errata Pins Tyan S1832DL Tiger Table of Contents Appendix 1 CPU Retention Module Options Appendix 2 Glossary System Resources Overview Chapter Icons Hardware Specifications/Features Disk Drive & System I/O Physical DimensionsBios Information Technical Support Software SpecificationsAlt.comp.periphs.mainboard.tyan 510 For Resellers Only Returning Merchandise for Service Unpacking Installation What’s the first thing I should do? Install the motherboard into your case Conforms to industry standard revision Plug in the power connector as shown Pin Chapter Next are the Com and Printer ports Connecting the USB and PS/2 ports Shows the USB ports and the PS/2 ports Installing your add-in cards is relatively simple but Next, you need to install your memory Install Finally, install your CPU Active Passive Installing CPU Retention ModulesInstalling the Active Processor Chapter Installing the Passive Processor Removing the CPU Setting JumpersYou are done Pin jumpers Or more pin jumpers Off Open This page has been intentionally left blank Quick References for Jumpers Onboard Resource Settings Map of Motherboard Jumpers PS/2 ports COM2 LPT1 COM1 USB ports LM79 PCI slots CPU Settings for 100MHz Bus CPU Settings for 66MHz Bus J10 External Pin Assignments 2x9 External Connector Proprietary Server Mgmt Connector Hardware Reset Switch Connector Installation Soft Power ConnectorSpeaker Connector Installation Windows 95 Users Chassis Intrusion Alarm ConnectorFlash Eeprom RAM Installation Hardware Cmos & Password Reset Dimm Cache Memory Pin Dimm Frequently Asked Questions Chapter This page has been intentionally left blank Bios Configuration Key Function Main Setup Floppy Drive a and B System Date/Time Type How to Configure Parameter Description Entering Drive Parameters Optimal Defaults Boot Sector Virus ProtectionFail-Safe Defaults Auto-Detect Hard Disks Advanced Cmos Setup Default Settings Chart Advanced Cmos Setup Quick Boot Settings Chart 2nd Boot Device 1st Boot Device3rd Boot Device Try Other Boot Devices Password Check Boot Up Num-LockBoot To OS/2 System Bios Cacheable Cache Bus ECC Default Primary VideoMPS Revision C000,16K Shadow and C400,16K Shadow Advanced Chipset Setup Enter Chipset Setup AGP S E R R USB Function Multi-Trans Timer Clks BX Master Latency Timer ClksUSB KB/Mouse Legacy Support Port 64/60 Emulation Dram Integrity Mode PCI1 to PCI0 AccessSetting Description Sdram RAS# to CAS# Delay AGP Low-Priority Timer Clks AGP Multi-Trans Timer AGP ClksAGP Parity Error Response 8bit I/O Recovery Time USB Passive Release 16bit I/O Recovery TimePIIX4 Passive Release TypeF DMA Buffer Control1 Power Management Setup Enter Power Management Setup Power Button Function Power Management/APMGreen PC Monitor Power State Acpi Aware O/S Hard Disk Power Down Mode Video Power Down ModePower Saving Type Standby/Suspend Timer Unit Slow Clock Ratio PC98 Power LEDDisplay Activity LAN Wake-up RTC Wake-up Plug and Play Setup Plug and Play Setup Default Settings Chart Plug and Play Aware O/S PCI Latency Timer PCI ClocksPCI VGA Palette Snoop Allocate IRQ to PCI VGA Offboard PCI IDE Secondary IRQ OffBoard PCI IDE Primary IRQPCI Slot n IRQ Priority DMA Channel n PCI Device Search Order Bios Devnode for Shadow RAMReserved Memory Address Peripheral Setup Default Settings Chart Peripheral Setup Power Interruption Default Settings ChartSerial Port2 Mode Overclock Warning Message Mode Description IR Transmission ModeParallel Port Mode IR Receiver Pin OnboardIDE Parallel Port IRQParallel Port DMA Channel Supervisor and User Security Flash Writer Utility Language Utility Beep Codes System Resources If the computer beeps Then Troubleshooting System Problems Error Message Explanation Displayed Error Messages OFF Board Parity Error Addr = Error Message Explanation Appendix Option Glossary Page Appendix Page Appendix Page Appendix Document # D1308-210