XDV Direct Vent Gas Fireplace
Installation & Operating Instructions
This gas appliance should be installed by a qualified installer in accordance with local building codes and with current
In the Commonwealth of Massachusetts, all gas fitting and installation of this heater shall only be done by a licensed gas fitter or licensed plumber.
FOR SAFE INSTALLATION AND OPERATION PLEASE NOTE THE FOLLOWING:
1.This fireplace gives off high temperatures and should be located out of high traffic areas and away from furniture and draperies.
2.Children and adults should be alerted to the hazards of high surface temperatures of this fireplace and should stay away to avoid burns or ignition of clothing.
3.CAUTION: Due to high glass surface temperature chil- dren should be carefully supervised when in the same room as fireplace.
4.Under no circumstances should this fireplace be modified. Parts removed for servicing should be replaced prior to operating this fireplace again.
5.Installation and any repairs to this fireplace must be per- formed by a qualified installer, service agency or gas sup- plier. A professional service person should be contacted to inspect this fireplace annually. Make it a practice to have all of your gas fireplaces checked annually. More frequent cleaning may be required due to excess lint and dust from carpeting, bedding material, etc.
6.Control compartments, burners and air passages in this fire- place should be kept clean and free of dust and lint. Make sure the gas valve and pilot light are turned off before you attempt to clean this fireplace.
7.The venting system (chimney) of this fireplace should be checked at least once a year and if needed your venting system should be cleaned.
8.Keep the area around your fireplace clear of combustible materials, gasoline and other flammable vapor and liquids. This fireplace should not be used as a drying rack for cloth- ing, nor should Christmas stockings or decorations be hung on or around the fireplace.
9.Under no circumstances should any solid fuels (wood, coal, paper or cardboard etc.) be used in this fireplace.
10.The flow of combustion and ventilation air must not be ob- structed in any way.
11.When fireplace is installed directly on carpeting, vinyl tile or any combustible material other than wood, the fireplace must be installed on a metal or wood panel extending the full width and depth of the fireplace.
12.This fireplace requires adequate ventilation and combustion air to operate properly.
13.This fireplace must not be connected to a chimney flue serving a separate solid fuel burning fireplace.
14.When the fireplace is not in use it is recommended that the gas valve be left in the OFF position.
WARNING: Check with your electronics manufacturer before installing a television or other electronic de- vice above this fireplace.
10009383
This appliance may be installed in an aftermarket per- manently located, manufactured home or mobile home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicat- ed on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used.
IMPORTANT:
PLEASE REVIEW THE FOLLOWING CAREFULLY
Remove any plastic from trim parts before turning the fireplace ON.
It is normal for fireplaces fabricated of steel to give off some expansion and/or contraction noises during the start up or cool down cycle. Similar noises are found with your furnace heat exchanger or car engine.
It is not unusual for your gas fireplace to give off some odor the first time it is burned. This is due to the curing of the paint and any undetected oil from the manufacturing process.
Please ensure that your room is well ventilated - open all windows.
It is recommended that you burn your fireplace for at least ten (10) hours the first time you use it. If the optional fan kit has been installed, place the fan switch in the “OFF” position during this time.
Locating Your Fireplace
E | A |
| B |
Y |
|
| |
|
|
| |
|
| C | X |
|
|
| |
D |
|
|
|
Y |
|
| B |
|
|
| |
| F |
|
|
|
| |
|
| |
Fig. 1 Locate gas fireplace. |
| |
A) Flat on wall | B) Cross corner | C) **Island |
D) *Room divider | E) *Flat on wall corner | F) Chase installation |
Y) 6” minimum |
|
|
NOTE: (fig. 1)
**Island (C) and Room Divider (D) installation is possible as long as the horizontal portion of the vent system (X) does not exceed 20’ (610 cm). See details in Venting Section.
*When you install your fireplace in(D) Room divider or (E) Flat on wall corner positions (Y), a minimum of 6” (153 mm) clear- ance must be maintained from the perpendicular wall and the front side edge of the fireplace.
Refer to (Y) in Figure 1.
3
