Codablock F Symbology, Code 11 Symbology | Videk 2030 guide

3.4 - Codablock F Symbology

Scan the following codes to enable/disable Codablock F symbology settings:

Codablock F On

Codablock F Off (Default)

Sample Codablock F Code

Note: When Codablock F and Code 128 decoding are enabled, there is some danger of mistakenly decoding a damaged Codablock F symbol as a Code 128 symbol. Therefore, Code 128 decoding should be disabled when Codablock F decoding is enabled.

3.5 - Code 11 Symbology

Scan the following codes to enable/disable Code 11 symbology settings:

Code 11 On (Default)

Code 11 Off

Code 11 Checksum 1 digit

Code 11 Checksum 2 Digit & Stripped from Result

Code 11 Checksum 1 Digit & Stripped from Result

Code 11 Sample with 1 Checksum Digit

3.6 - Code 39 Symbology

Scan the following codes to enable/disable Code 39 symbology settings:

Code 39 On (Default)	Code 39 Off	Enable Checksum
Disable Checksum (Default)	Enable Checksum and Strip From Result
Code 39 Extended Full ASCII On	Code 39 Extended Full ASCII Off (Default)

Save Settings	K11020 VisionSensor™ 2030 User Manual, Rev. E, Software ver. 3.1.1000, August 3, 2007 - 28

Image 34

Videk 2030 manual Codablock F Symbology, Code 11 Symbology, Code 39 Symbology, Codablock F On Codablock F Off Default

Contents

Part Number K11020, Rev. E, August 3 Statement of Agency Compliance Laser/LED Radiation Save Settings Table of Contents VS 2030 Programming Symbology Settings UPC/EAN/JAN Appendix a Reader Specifications Getting Started Introduction Powering On/Off Reader Unpacking Keypad/Icon Overview Description of Button Function Power Icons Icon Description Introduction RS232 Batch Cable-Detect DefaultBatch Operation RS232 Considerations Cabled Operation Introduction USB Cable Installation Guide USB Keyboard Default USB Downloader USB Virtual COM 1 Way Mode Mode RS232 One Way Mode RS232 Cable Installation GuideRS232 One Way Mode Save Settings Baud Rate 1200 2400 4800 9600 19200 38400 Default 115200 Data Bits Data Bits DefaultStop Bits Default Even Odd None Default Cabled Reader Time Out Settings Cabled 2 hours Cabled Always Default Reader Feedback Guide RS232 To read a symbol with the VS Targeting and Reading Techniques Imager Field of View and Resolution Decode Zone Removing and Attaching Handle Optimization and Trigger Programming Introduction DOT Global Trigger Optimization Matrix Left Trigger Programming Read Codes with Both Imagers DefaultLeft Trigger Optimization Matrix Read with Near-Field Imager only Right Trigger Programming Right Trigger Optimization MatrixRead Code with Near-Field Imager only Handle Optimization Matrix Handle Trigger Programming Continuous Scan Far Field Only On Off DefaultContinuous Trigger Optimization Matrix Both Near & Far Field On Motion Detection Scan Settings Continuous Scan SettingsSeconds Default VS 2030 Programming Symbology Settings Aztec Symbology Codabar Symbology Code 39 Symbology Codablock F SymbologyCode 11 Symbology Codablock F On Codablock F Off Default Code 93 On Default Code 93 Off Code 93 SymbologyCode 128 Symbology Sample Trioptic Code Data Matrix Symbology Composite SymbologiesComposite On Composite Off Default Interleaved 2 of 5 Symbology Maxicode Symbology MSI Plessy Symbology Matrix 2 of 5 SymbologyMSI Plessy On MSI Plessy Off Default Sample MSI Plessy NEC 2 of 5 On NEC 2 of 5 Off Default NEC 2 of 5 SymbologyPharmacode Postal Symbologies Advanced Postal Symbologies UK ID Tag On Default UK ID Tag Off QR Code Symbology RSS Symbology Telepen Symbology UPC/EAN/JAN Reader Feedback and Special Settings Code Readability Index Volume and Vibration SettingsOff Default Low Medium Vibrate On / Beep On Vibrate On / Beep Off Readability Index Output Disable Backlight Intensity SettingsLow Med Default High Laser Settings Backlight Timeout SettingsReader Power Off Settings Reader ID and Firmware Version Reader Settings LockReader Settings Locked Reader ID and Firmware Keyboard Support Time Stamp SettingsUS English Default US English Leading No Leading French German Advanced Decode Performance Set Targeting Zone Tolerances Enable Continuous IlluminationContinuous Illumination 100 125 Windowing Medium Code Windowing Small Code Windowing Large 2-Dimensional Codes 640 x 640 pixels Enable VGA 640 x VGA & Megapixel SettingsCodes Enable Sxga 1024 x Mirror Decoding Adding a Prefix or Suffix and Reader Text Commands Suffix Settings Prefix SettingsPrefix Comma Prefix Space Reader Text Commands On Erase Prefix and Suffix SettingsReader Text Commands Erase Prefix & Suffix Data VS 2030 Maintenance and Troubleshooting Reset Reader to Factory Defaults General Safety Information Terms of Warranty WarrantyLimited Warranty Warranty Coverage and Procedure VS 2030 Accessories Troubleshooting General Cleaning the VS 2030 Window VS 2030 MaintenanceTechnical Support and Returns Appendix a Reader Specifications Physical Characteristics Performance Characteristics User Environment Appendix B Mechanical & Electrical Specifications Dimensions USB Connector Pin Out Diagram Pin DIN Connector Pin Out Diagram RS232 Connector Pin Out Diagram Appendix C Pharmacode Settings Pharmacode Settings Pharmacode Settings con’t Appendix D Factory Default Settings Symbology Defaults Default SettingsControl Setting Defaults RS-232 Interface Setting Defaults Batch Mode Setting Defaults Appendix E Programming Codes Appendix E Table of Contents Right Trigger Optimization and Settings Global All Trigger Optimization and SettingsLeft Trigger Optimization and Settings Handle Trigger Optimization and Settings Continous Trigger Optimization and Settings Symbologies Code 39 On Default Symbol Readability Index Reader Feedback Illumination Settings Backlight SettingsLaser Settings Keypad Volume Miscellaneous Settings Reader Text CommandsReader Settings Locked Targeting Zone Tolerances Batch Log Only Mode Batch Send & Log Mode VS 2030 Programming Codes RS232 Interface Suffix Tab USB Keyboard Mode only RS232 Interface Baud RateSuffix Erase/None Default RS232 Interface Baud Rate Baud Rate VS 2030 Programming Codes Handle Trigger Optimization Continous Trigger Digit Digit & Strip from Result Code 39 Off Code 39 Enable 5 with Control Character Stripped Allow ALL Data Matrix Codes DefaultAllow only Programming Data Matirx Codes Postal Codes Postnet On Japan Post On ID Tag/S18D Off UK ID Tag On Default UK ID Tag Off QR Code Inverse On QR & Micro QR Code On QR Code On QR Code Off Default QR Code EnableRSS Expanded On UPC Off UPC Extension Off Backlight Intensity High Vibrate On Beep On Vibrate On Beep OffBacklight Intensity Low Backlight Off Mirroring Off Default Default Reader Power Off 1 HourKeypad Volume High Continous Illumination US English ctrl + char Lockout Link Mode