INSTRUCTIONS MANUAL

VACUUM PHASE

1.Upon completion of the RECOVERY phase it is possible to start the vacuum phase by opening the high- and low-pressure valves, pressing the SEL key until the LED corresponding to “EVACUATE” lights, and then pressing GO. The vacuum time can be set as follows. Press SEL until the “EVACUATE” LED lights, then press ENTER; at this point the first digit on the left of the displaywill begin to flash. Press the INCREASE key until the desired digit appears. Likewise, press the ARROW and INCREASE keys to change the other digits. When setting is complete, press the ENTER key to confirm the vacuum time value.

2.During the vacuum phase, the display will clock its duration. Leave the machine running until the displayreads 0000 and the pump stops automatically.

3.Close all the valves and read the vacuum value on pressure gauges (A1) and (A2). Wait for about 2 minutes, and then check that the pressure has not increased during the interval. An increase in pressure signals leaks in the A/C system. Locate and eliminate the leaks; repeat the vacuum phase.

WARNING: Avoid breathing A/C refrigerant and lubricant vapor mist. Exposure may irritate eyes, nose, and throat. To remove HFC-134a from the A/C system, use service equipment certified to meet the requirements of SAE J2210 (HFC-134a recycling equipment). Additional health and safety information may be obtained from additional refrigerant and lubricant manufacturers.

NEW OIL INJECTION

You can inject virgin lubricating oil into the vehicle A/C system at this time. Make certain that the Oil Charge Bottle has sufficient quantity of oil. Cautiously open the Oil Charge valve until the same amount of oil that was recovered in the RECOVERY AND RECYCLING operation is removed from the container and replaced back into the vehicle's A/C system. The oil will be drawn into the vehicle A/C system by the deep vacuum that was obtained while evacuating. The subsequent charging of refrigerant will ensure all of the oil will be charged from the lines and hoses.

RECHARGE AN A/C SYSTEM

WARNING: Always wear safety goggles and hand protection when working with refrigerants. Failure to follow these procedures may result in serious injury. Due to the extreme cold temperatures associated with the use of refrigerants, any contact with the eye can cause blindness and contact with the bare skin can cause burns or frostbite.

CAUTION: When charging a vehicle do not lean on the machine as this may affect the scale readings. Inaccurate weight measurements may result. The vehicle system can be damaged if weights are not measured accurately.

During this phase, the correct refrigerant charge is returned to the vehicle’s A/C system.

1.Press the SEL keyuntil the “RECHARGE” LED lights.

2.Proceed as described below to set the quantity of refrigerant fluid to be charged. Press the ENTER key. The first digit on the left of the display will begin to flash. Press the INCREASE keyuntil the desired value appears. (Digits read in pounds and ounces, or kilograms.) Likewise, press the ARROW and INCREASE keys to change the values of the other digits. Press ENTER when setting is completed to confirm the values. The quantity of fluid required for filling the system is usually reported on a data plate in the engine compartment of the vehicle. If the quantity is not known, consult the relevant system operating and maintenance manuals.

18

Page 17 Page 19
Page 18
Image 18
Viper VR-6000 owner manual Vacuum Phase, Recharge AN A/C System
Page 17 Page 19

VR-6000 specifications

The Viper VR-6000 is an innovative addition to the realm of virtual reality headset technology, designed to offer users an immersive and visually stunning experience. Built with meticulous attention to detail, the VR-6000 provides an ideal mix of high-end performance, comfort, and cutting-edge features that cater to both gamers and tech enthusiasts alike.

One of the standout characteristics of the Viper VR-6000 is its high-resolution display. The headset boasts a dual 4K OLED screen that delivers an exceptional pixel density, resulting in incredibly sharp visuals and vibrant colors that breathe life into the virtual environments. This feature significantly enhances the sense of realism, making every gaming session or virtual experience captivating.

The VR-6000 is powered by advanced refresh rate technology, providing a refresh rate of up to 120 Hz. This ensures smooth and fluid visuals, minimizing motion blur and enhancing responsiveness during fast-paced action scenes. Coupled with low-latency tracking, players can enjoy an almost instantaneous response as they move within their virtual space, making the experience feel more natural and engaging.

Comfort is another focal point of the Viper VR-6000 design. The headset has a lightweight frame and adjustable padding, which accommodates prolonged use without discomfort. It is designed to fit a wide range of head sizes, with a customizable strap system ensuring a secure and snug fit. Additionally, the integrated audio system features spatial sound technology that offers 3D audio experiences, allowing users to hear sounds from all directions, further enhancing immersion.

On the technological front, the Viper VR-6000 comes equipped with advanced motion tracking sensors. Utilizing a combination of inside-out tracking and external base stations, it allows for precise movement detection, which is crucial for room-scale VR experiences. Users can move freely within their designated space, and the system accurately reflects these movements in real time.

Compatibility is another highlight of the VR-6000. It supports a wide range of platforms, including both PC and console, allowing users to access an extensive library of VR titles. Moreover, the headset includes easy-to-use connectivity options, such as wireless capability and USB-C support, ensuring seamless integration with various devices.

In summary, the Viper VR-6000 represents a significant leap in virtual reality technology, offering an impressive array of features and capabilities. With its high-resolution display, advanced motion tracking, exceptional comfort, and compatibility with multiple platforms, it stands out as a top choice for those seeking an immersive VR experience. Whether for gaming, simulations, or interactive media, the VR-6000 promises to elevate the way users engage with the virtual world.
Top Page Image Contents