INSTRUCTIONS MANUAL

3.Open the high- and low-pressure valves (if previouslyclosed) and press the GO key.

4.The machine will stop automatically when the preset quantity has been charged. If the A/C system pressure increases to equal the tank pressure, and the charge is not complete, it will be necessary to draw the remaining refrigerant into the system using the vehicle compressor as outlined below.

5.Close the high- and low-pressure valves.

6.Start the vehicle motor and switch on the A/C system, and allow both to run for at least 3 minutes. At this point the system will be at steady state and it will be possible to check the high and low side values on the relative pressure gauges.

7.Disconnect ONLY the high-pressure quick-connect coupling (if necessary, switch the engine off). Then, with the A/C system still running, open the high and low pressure taps to force the A/C system to draw up the refrigerant contained in the hoses.

8.After about 1 (one) minute, disconnect the low-pressure couplings of the VIPER VR- 6000 from the vehicle A/C system and switch off the engine.

WARNING: When removing hoses from the vehicle, use extreme caution. Wear gloves and eye protection. Take care not to allow refrigerant to enter the eyes. Liquid refrigerant will cause severe burns and/or frostbite to exposed skin, blindness if sprayed into the eyes, and even the possibility of death if inhaled.

RECOVERING THE REFRIGERANT IN THE HOSES.

1.Set the MAIN POWER switch ON and open the high side and low side valves on the front of the machine.

2.Press and hold the SEL keyuntil the LED until the LED corresponding to “RECOVERY” lights; then press GO. At this point the RECOVERY/RECYCLING phase will begin; the “RECOVERY” LED will flash.

3.When all of the refrigerant has been removed from the hoses, the machine will automatically shut off and the lamp in the switch will extinguish. To avoid going through an “unnecessary and time consuming oil dumping phase”, press the stop keyas soon as pressure in low pressure hose reaches zero.

4.Close the High Side Valve and Low Side Valve and turn off the machine’s main power.

19

Page 19
Image 19
Viper VR-6000 owner manual Recovering the Refrigerant in the Hoses

VR-6000 specifications

The Viper VR-6000 is an innovative addition to the realm of virtual reality headset technology, designed to offer users an immersive and visually stunning experience. Built with meticulous attention to detail, the VR-6000 provides an ideal mix of high-end performance, comfort, and cutting-edge features that cater to both gamers and tech enthusiasts alike.

One of the standout characteristics of the Viper VR-6000 is its high-resolution display. The headset boasts a dual 4K OLED screen that delivers an exceptional pixel density, resulting in incredibly sharp visuals and vibrant colors that breathe life into the virtual environments. This feature significantly enhances the sense of realism, making every gaming session or virtual experience captivating.

The VR-6000 is powered by advanced refresh rate technology, providing a refresh rate of up to 120 Hz. This ensures smooth and fluid visuals, minimizing motion blur and enhancing responsiveness during fast-paced action scenes. Coupled with low-latency tracking, players can enjoy an almost instantaneous response as they move within their virtual space, making the experience feel more natural and engaging.

Comfort is another focal point of the Viper VR-6000 design. The headset has a lightweight frame and adjustable padding, which accommodates prolonged use without discomfort. It is designed to fit a wide range of head sizes, with a customizable strap system ensuring a secure and snug fit. Additionally, the integrated audio system features spatial sound technology that offers 3D audio experiences, allowing users to hear sounds from all directions, further enhancing immersion.

On the technological front, the Viper VR-6000 comes equipped with advanced motion tracking sensors. Utilizing a combination of inside-out tracking and external base stations, it allows for precise movement detection, which is crucial for room-scale VR experiences. Users can move freely within their designated space, and the system accurately reflects these movements in real time.

Compatibility is another highlight of the VR-6000. It supports a wide range of platforms, including both PC and console, allowing users to access an extensive library of VR titles. Moreover, the headset includes easy-to-use connectivity options, such as wireless capability and USB-C support, ensuring seamless integration with various devices.

In summary, the Viper VR-6000 represents a significant leap in virtual reality technology, offering an impressive array of features and capabilities. With its high-resolution display, advanced motion tracking, exceptional comfort, and compatibility with multiple platforms, it stands out as a top choice for those seeking an immersive VR experience. Whether for gaming, simulations, or interactive media, the VR-6000 promises to elevate the way users engage with the virtual world.