Manuals / Wacom / Computer Equipment / Computer Monitor

Wacom PL-521, DTF-521 manual LCD monitor cabling diagram, Adapter may damage the unit

Models: DTF-521 PL-521

1 52

Download 52 pages 41.53 Kb

Page 13

DTF521_Manual.fm Page 11 Tuesday, February 28, 2006 10:36 AM

LCD monitor cabling diagram

Do not attach the USB data cable until instructed to do so.

DTF-521/PL-521, rear view

– B –

DC IN (12V)

ANALOG RGB OUT

ANALOG RGB IN

– A –

VGA cable

The ANALOG RGB OUT port is used to connect a second VGA device such as a projector or monitor that mirrors the pen display. Be sure to fully install the pen display hardware and software before connecting a projection device to the unit. Do not connect or disconnect any cable while the pen display or your computer are turned on.

Video card

VGA port

Rear panel of your computer

Power adapter

– C –

To AC outlet

CAUTION Use only the power adapter that came with the DTF-521/PL-521; use of an improper power

adapter may damage the unit.

Do not connect or disconnect the video or power cables while the DTF-521/PL-521 or your computer are turned on – this can damage the LCD monitor or computer video card.

Make sure that the display refresh rate does not exceed 70 Hz for XGA mode, or 75 Hz for other modes.

Installation page 11

Image 13

Wacom PL-521, DTF-521 manual LCD monitor cabling diagram, Adapter may damage the unit

Contents

Pen Display This page intentionally left blank Introduction and Overview Temperature and humidity Precautions on USE and HandlingPhysical location EnvironmentHg Lamps Inside this Product Contain Mercury and Must be HandlingDTF521Manual.fm Page 4 Tuesday, February 28, 2006 1036 AM Contents Unpacking Your PEN Display Package contentsFront view PEN Display ComponentsRear view System requirements InstallationVGA connector LCD monitor installationAdapter may damage the unit LCD monitor cabling diagramDTF521Manual.fm Page 12 Tuesday, February 28, 2006 1036 AM USB cable installation Pen tablet installationPen tablet cabling diagram Next steps Software installationWorking with Your PEN Display Setting up your work areaPen components Using the penPen operations Opening the control panel CustomizingCustomizing the pen Control panel overviewCalibrating your pen display Customizing the side switch button functions Adjusting double-clickControl panel details DTF521Manual.fm Page 22 Tuesday, February 28, 2006 1036 AM DTF521Manual.fm Page 23 Tuesday, February 28, 2006 1036 AM Factory presets, auto-sync, and user settings Adjusting the LCD monitorWorking with on screen display settings Enter buttonMenu Position DTF521Manual.fm Page 26 Tuesday, February 28, 2006 1036 AM Adjusting pitch and phase Power saving mode Sync Power savingVideo Power consumption Testing the DTF-521/PL-521 TroubleshootingIf there is no display Verify that the tablet and pen are working General display problems Display troubleshootingDisplay ripples or ﬂickers VGA problemsGeneral problems Pen tablet troubleshootingTroubleshooting on DTF521Manual.fm Page 35 Tuesday, February 28, 2006 1036 AM Windows XP Windows-Speciﬁc ProblemsSupport. See Technical support options on Macintosh-Speciﬁc ProblemsTechnical support options Japan Obtaining driver downloadsAsia Paciﬁc English China Appendix CleaningCaring for your pen display Replacing the pen tipUsing an alternate mount or stand Windows XP or XP Uninstalling the DTF-521/PL-521Windows 98SE, Me, or Macintosh OSGeneral speciﬁcations Product speciﬁcationsLCD monitor Power adapter Purchasing parts and accessoriesPen tablet Pen model FP-320Federal Communications Commission FCC notice Radio and television interferenceCE declaration Warranty Warranty Service Outside of the U.S.A. and Canada Warranty Service in the U.S.A. and CanadaNorth and South America contact Europe, Africa and Middle East Software License Agreement License and WarrantyEntitlement to Use the Software Important Notice to CustomersGermany This page intentionally left blank Appendix