Wayne-Dalton 9300 installation instructions Pull Rope, Trolley Operator, Cleaning

	Pull Rope
Tools Needed:	WARNING	SECTION	SCREW EYE
		BOTTOM	NO. 6

Power Drill	DO NOT INSTALL PULL ROPES ON				JAMB
1/8” Drill Bit	DOORS WITH ELECTRIC OPERATORS.
	CHILDREN MAY BECOME ENTANGLED				HEIGHT50”
	Measure and mark the jamb approximately 48” to 50”
Tape Measure	IN THE ROPE CAUSING SEVERE OR
	FATAL INJURY.
	(1220 to 1270 mm) from floor on the right or left side of				48”-
	jamb. Drill 1/8” pilot hole and install No. 6 screw eye.		SMALL EYE
	Locate the roller carrier at the bottom of the door;			BOLT	BOTTOM
			1/8” x 3/4”
	remove the self tapping screw. Using the roller carrier				SECTION
	as a guide, drill a 1/8” diameter hole through the u-bar.
	Insert the 1/8” x 3/4” eye bolt and secure to the u-bar
	with one nut. Tie pull rope to the eye bolt.
	Tie pull rope to No. 6 screw eye , installed on jamb as			NUT
	shown.				SMALL EYE
					BOLT
				SUITABLE MOUNTING	OPERATOR
		Trolley Operator			RAIL
				SURFACE (2 X 6)
				LUMBER MIN.
Tools Needed:		WARNING
	OPERATOR MUST BE TESTED AT TIME
	OF INSTALLATION AND MONTHLY
	THEREAFTER AS DESCRIBED IN YOUR			HEADER
	INSTALLATION INSTRUCTIONS AND				DOOR ARM TO
	OWNER’S MANUAL, TO ENSURE THAT				OPERATOR BRACKET
	DOOR SAFETY FEATURES FUNCTION.				PERFORATED
	FAILURE TO TEST OR MAKE ANY
				OPERATOR	ANGLE
	NECESSARY ADJUSTMENTS OR REPAIRS,
				RAIL
	CAN RESULT IN SEVERE OR FATAL
	INJURY.			STRUCTURALLY SOUND
				FRAMING MEMBERS
	1. Install operator rail 1/2” to 1-1/2” (13 - 38 mm) above
		high arc of top section of the door.
	2. Attach operator bracket to a suitable mounting surface
		(2” x 6”) lumber minimum.
	3. Mount operator to ceiling so that 1” to 1-1/2” (25 - 38
		mm) clearance is maintained between trolley rail and
		top section when door is fully open (trolley rail will slope
		down towards rear).		PERFORATED
	4. Attach operator to structurally sound ceiling framing			ANGLES
		members.
	5.	Attach door arm to operator bracket.
	IMPORTANT: ANGLE MUST BE ATTACHED TO				OPERATOR
	FRAMING MEMBER(S).

Cleaning

Like any other exterior surface, Wayne-Dalton garage doors will have dirt exposure from atmospheric conditions. Ordinarily, the cleaning action of rainfall will be adequate to wash the door, or the door can be washed periodically by hosing with a garden hose and clear water (in particular) for the areas not accessible to rain. If you desire to do a more thorough cleaning, or where soil collection conditions occur, follow these simple instructions.

1.Use a soft-bristled, long-handled washing brush. It attaches to your garden hose and makes washing your garage door easier. Do not rub vigorously which may create glossy areas over the vinyl finish.

2.For hard-to-remove dirt, such as soot and grime found in industrial areas, wash the garage door down with a mild solution consisting of the following ingredients: One cup detergent (with less than 0.5% phosphate) dissolved into five gallons of warm water.

NOTE: The use of detergents containing greater than 0.5% phosphate is not recommended for use in general cleaning of garage doors.

NOTE: Be sure to clean behind weather stripping on both sides and top of door.

3.Start at the bottom and work up to the top, as less streaking will result. Immediately following all washing operations, thoroughly rinse the surface area with fresh water from a garden hose.

This cleaning and maintenance information is suggested in an effort to be of assistance; however, manufacturer cannot assume responsibility for results obtained which are dependent on the cleaning solution and method of application.

CAUTION: DO NOT PAINT DOOR. PAINTING DOOR WILL VOID YOUR WARRANTY.

26

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com