Manuals / Wayne-Dalton / Household Appliance / Water Pump

Wayne-Dalton 9700 installation instructions Tools Required, Removing An Existing Door

Models: 9700

1 32

Download 32 pages 17.33 Kb

Page 5

Tools Required

Tools Required

Power Drill	Ratchet Wrench	Pliers/Wire Cutters	Tape Measure	1/8”, 3/16” Drill Bits
Phillips Head Screwdriver	Flat Tip Screwdriver	Pencil	Needle Nose Pliers	Gloves
7/16”, 1/2”, 9/16”	7/16” Socket Driver	3/8”, 7/16”, 1/2”, 9/16”	Safety Glasses
Sockets		Wrenches
				Step Ladder
Hammer	Vice grips	Vice clamps	(2) Saw Horses

Removing An Existing Door

IMPORTANT: Counterbalance spring tension must always be released before any attempt is made to start removing an existing door.

WARNING

A powerful spring releasing its energy suddenly can cause severe or fatal injury. To avoid injury have a trained door systems technician, using proper tools and instructions, release the spring tension.

For detailed information see supplemental instructions “Removing an Existing Door /Preparing the Opening”. These instructions are available at no charge from Wayne-Dalton, a Division of Overhead Door Corporation, P.O. Box 67, Mt. Hope, OH 44660, or at www.Wayne-Dalton.com.


Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your	5
local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com

Image 5

Wayne-Dalton 9700 installation instructions Tools Required, Removing An Existing Door

Contents

Torquemaster Plus - Single and Double Spring 9700Definition of key words used in this manual Table of ContentsPackage Contents Door Section Identification Removing An Existing Door Tools RequiredIMPORTANT Closely inspect jambs, header and Preparing the Openingmounting surface. Any wood found not to be sound must be replacedTracks InstallationAttaching Flagangles to Vertical Tools Needed NoneTools Needed Hammer Installing Jamb BracketsHorizontal Angles Tools Needed None DrumsBottom Section Vertical Tracks Tools Needed 3/16” Drill Bit Power DrillStacking Sections 7/16” Socket Driver Tape Measure LevelU-Bar Stacking Sections - ContinuedOperator Bracket Top Section Top BracketsDO NOT RAISE DOOR UNTIL FlaganglesINJURY DO NOT RAISE DOOR UNTILTools Needed 7/16” Wrench Step Ladder Adjusting Top BracketsTorqueMaster Spring Tube Center Bracket Bushing 1-1/2Wraps Cable Drums/ Drum WrapsEnd Brackets AssemblySecuring Center Bracket 7/16” Wrench 7/16” Socket Driver Step LadderSecuring Door for Spring Winding Cable AdjustmentTools Needed 2 Vice Clamps IMPORTANT ENSURE THE CABLE ISit is recommended that Winding Springsleather gloves be worn while winding the TorqueMasterSecuring Drum Wraps Winding Springs ContinuedTools Needed IMPORTANT Mark number of springRaising door further can Rear Supportresult in door falling and cause severe or fatal injuryFULL TENSION OF THE SPRING SPRING TURN CHARTRear Support Continued Instructions TorqueMaster Plus ResetTools Needed TorqueMaster Plus Reset Instructions ContinuedPlace vice clamps TorqueMaster Plus Reset Instructions ContinuedTools Needed Power Drill DO NOT INSTALL PULL ROPESPull Rope ON DOORS WITH ELECTRICINSTALLATION INSTRUCTIONS AND OF INSTALLATION AND MONTHLYTrolley Operator OPERATOR MUST BE TESTED AT TIMEPainting CleaningPainting Continued Lifetime Limited Warranty Model Thank you for your purchase Please Do Not Return This Product To The Store