13 | Center Bearing Bracket | |
| ||
Tools Needed: | Measure to locate the center of the door | |
Power Drill | and mark a vertical pencil line on the | |
mounting surface above the door, to | ||
| ||
7/16” Socket | indicate the center line of the door. Then, | |
Driver | measure from the center of the bearing, in | |
Level | one of the end bearing brackets, DOWN to | |
the top of the door. Using that dimension, | ||
| ||
Tape Measure | measure UP from the top of the door | |
Pencil | and mark a horizontal pencil line on the | |
mounting surface, intersecting the vertical | ||
1/4” Torx Bit | ||
pencil line. Now align the edge of the center |
Horizontal line
Center of end bearing bracket
Mounting surface
Vertical line
Equal distance
Center bearing bracket
Step Ladder | bearing bracket along the vertical pencil | |
line on the mounting surface. Center the | ||
| ||
| bearing bracket on the horizontal line. This | |
| will ensure the torsion tube is level between | |
| the center and end bearing brackets. Attach | |
| the center bearing bracket, in this location, | |
| to the mounting surface, using | |
| (2) 5/16” x | |
| x 2” | |
| IMPORTANT: Use the 5/16” x | |
| ||
| if mounting surface is mounted | |
| over masonry. | |
| screw MUST be attached through the | |
| bottom hole of the center bearing | |
| bracket. |
(1) 5/16” x
Mounting surface
Horizontal line
(1)5/16” x
(1)5/16” x 2”
(1)5/16” x
Center bearing bracket
Vertical line
14 | Torsion Spring Assembly |
| |
Tools Needed: | IMPORTANT: Right and left hand is |
Step Ladder | always determined from inside |
| the garage looking out. |
| NOTE: Identify the springs provided as |
| either right hand wound (red winding |
| cone), which goes on the LEFT HAND |
| SIDE or left hand wound (black winding |
| cone), which goes on the RIGHT HAND |
| SIDE. |
| Facing the inside of the door, lay the |
| torsion tube on the floor. Lay the spring |
| with the black color coded winding |
Left hand cable drum red
|
|
| RED | IDE | |
|
|
| S | ||
|
|
| ND | ND | |
|
|
| U | HA |
|
|
| WO EFT |
| ||
H | ND | L |
|
| |
HA | CONE |
|
| ||
T |
|
|
|
| |
WINDING |
|
|
|
| |
RIG |
|
|
|
|
|
Right hand cable drum black
|
| ck S | ||
| la |
| IDE | |
| ND |
| ||
| B |
|
| |
| ND | HA |
| |
| U ht |
|
| |
| WO rig |
|
|
|
ND |
|
|
| |
HA | CONE |
|
|
|
Left |
|
|
|
|
WINDING | Torsion |
|
|
|
|
|
|
|
tube
Nylon Center bracket bushing
cone and the black color coded cable |
drum, at the right hand end of the tube. |
Lay the spring with the red color coded |
winding cone and the red color coded |
cable drum, at the left hand end of the |
tube. |
Nylon Center | Right | |
hand | ||
bracket bushing | ||
cable | ||
RIGHT HAND WOUND | ||
drum | ||
RED WINDING CONE | black |
LEFT HAND SIDE | Left HAND WOUND | |
Left hand cable | ||
Black WINDING CONE | ||
drum red | Torsion right HAND SIDE | |
| tube |
16Please Do Not Return This Product To The Store. Contact your local
To find your