18 | Winding Torsion Spring(s) |
|
|
|
|
|
|
| |
Tools Needed: | Position a ladder slightly to the side of spring |
|
|
|
so that the winding cone is easily accessible, |
|
|
| |
Step Ladder |
|
|
| |
yet your body is not in direct line with the |
|
|
| |
3/8” Wrench | winding bars. Check the label attached to the |
|
|
|
spring warning tag for the required number of |
|
|
| |
Approved Winding |
|
|
| |
complete turns to balance your door. |
|
|
| |
Bars | 9’0” Door Height = Approx |
|
|
|
| 10’0” Door Height = Approx |
|
|
|
| CAUTION: Use winding bars of |
|
|
|
| correct diameter to wind springs. |
|
|
|
| Do not use screwdrivers or other |
|
|
|
| items to wind springs. |
|
|
|
| WARNING |
|
|
|
| Failure to use only approved |
|
|
|
| steel winding bars of |
|
|
|
| correct diameter can result |
| Spring | INSTALLATION |
| in severe or fatal injury. |
|
| |
| WARNING |
|
| |
| To avoid possible severe or |
| Winding | |
| fatal injury, if you are |
| ||
|
| cone | ||
| Torsion |
| ||
| inexperienced in winding |
|
| |
| tube |
|
| |
| torsion springs, have springs |
|
|
|
| wound by a trained door |
|
| Approved |
| systems service technician, |
|
| |
|
|
| Winding bars | |
| using proper tools and |
|
| |
|
|
|
| |
| instructions. |
|
|
|
| WARNING |
|
|
|
| Prior to winding or making |
|
|
|
| adjustments to the springs, ensure |
|
|
|
| you’re winding in the proper |
|
|
|
| direction as stated in the |
|
|
|
| Installation Instructions. |
|
|
|
| Otherwise the spring fittings may |
|
|
|
| release from spring if not wound | Set screws |
|
|
| in the proper direction and could |
|
|
|
| result in severe or fatal injury. |
|
|
|
| Alternately inserting the steel winding bars |
|
|
|
| into the holes of the spring’s winding cone, |
|
|
|
| rotate the winding cone upward toward |
|
|
|
| ceiling, 1/4 turn at a time, until the required |
|
|
|
| number of complete turns for your door height |
|
| Spring |
| is achieved. As the last 1/8 to 1/4 turn is |
|
|
|
| achieved, securely hold winding bar while |
|
|
|
| tightening both set screws in winding cone to |
|
|
|
|
|
|
| |
| contact the tube, tighten screws one full turn). |
|
|
|
| Carefully remove winding bar from winding |
| Winding |
|
| cone. Proceed to wind the second spring in | Torsion |
| |
| the same manner. While holding the door | cone | Approved | |
| down, to prevent it from rising unexpectedly, in | tube |
| Winding bars |
|
|
| ||
| the event the spring(s) were overwound, |
|
|
|
| carefully remove vice grips from the torsion |
|
|
|
| tube and the vice clamps from the vertical |
|
|
|
| tracks. |
|
|
|
| Please Do Not Return This Product To The Store. Contact your local | 19 |
To find your