Questions?, Patent Pending | Weider WESY97300 instruction

PATENT PENDING

Model No. WESY97300

Serial No.

(Write the serial number in the space above for reference.)

Serial Number Decal

QUESTIONS?

As a manufacturer, we are com- mitted to providing complete customer satisfaction. If you have questions, or find there are miss- ing or damaged parts, we will guarantee you complete satisfac- tion through direct assistance from our factory.

TO AVOID UNNECESSARY DELAYS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER

HOT LINE. The trained techni- cians on our customer hot line will provide immediate assis- tance, free of charge to you.

CUSTOMER HOT LINE:

1-800-999-3756

Mon.–Fri., 6 a.m.–6 p.m. MST

CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual	USER'S MANUAL
for future reference.	USER'S MANUAL

Page 1

Image 1

Weider user manual Questions?, Patent Pending, Model No. WESY97300 Serial No, Serial Number Decal, Customer HOT Line

Contents

Patent Pending QUESTIONS?Model No. WESY97300 Serial No Serial Number Decal Limited Warranty Table of Contents Ing down Important Precautions Before YOU Begin Using the Weider PRO 9730 Home Gym System Frame Assembly AssemblyFollowing Tools not Included are Required for Assembly Before beginning assembly, be sure that Do not tighten Nylon Locknuts yet This side Lubricate Pins Slide eight Weights 25 onto the WeightSame side Must be at That the indicated holes are on the side Shown Frame Assembly ARM Assembly Tap two 1 Retainers 69 and a 1 Round 2 Bolt 7 and a 3/8 Nylon LocknutAttach the Left Arm 47 in the same manner Welded Brackets Lubricate Axle Locate the High Cable Be sure that Cable AssemblyPulley Bracket must Route the High Cable 23 around one Assembly8 Nylon Locknut Frame 55 with a 3/8 x 1 3/4 Bolt 87 and a 3/8 Nylon Locknut Two 5/16 Nylon Jam Nuts Locate the Press CableCable to pivot Locknut Slide the Low Cable into place under the 3 1/2 Low Pulley Locate the Low CablePress Frame 17 and that the Cable is Press Frame Pulley as shown Be sure that Cable Trap is turned to hold the CableWrap the Low Cable 86 around a V-Pulley Locate the Rear Cable 95. Attach the Rear Onto the Bolt. Do not overtighten the Nylon Locknut Cable must be routed from the direc- tion shown 4 Bolt 87 and a 3/8 Nylon Locknut Seat Plate to a Seat 13 with two 1/4 x 3/4 Screws Two 1/4 WashersUpright with a 5/16 x 2 3/4 Carriage Bolt A Seat Knob Upright 42 with two 1/4 x 2 1/2 Screws Two 1/4 Washers Seat AssemblyThick End Tighten a 1/4 Nylon Locknut 2 with a With the Bolt and a 5/16 Nylon Locknut Press a 1 1/2 Square Inner Cap 32 into the Leg LeverLubricate-33 Pin Misc Changing the Weight Setting AdjustmentAttaching the LAT BAR or Nylon Strap to High Pulley Station Cable with two Cable Clips Attach one end of the Chain 52 to the Low Cable Attaching the LEG Lever to the LOW Pulley StationAttaching and Removing the Seats With the 5/16 x 2 3/4 Carriage Bolt 14 and the Seat Knob Lbs Weight Resistance Chart From the Weight Tube not shown or remove TROUBLE-SHOOTING and MaintenanceTightening the Cables Woven cable, the type of cable used on the home Weight Stack Cable DiagramsRear Base Press Cable Rear Upright High Cable Ordering Replacement Parts WESY97300 R1097A Check to see if it has been pre-assembled 16 x 2 3/4 Carriage Bolt Retainer Round Inner Cap Remove this Part LIST/EXPLODED Drawing from the Manual Description Part LIST-Model No. WESY97300 Exploded