Seat Assembly, Thick End, 1/4 x 2 1/4 Screw

SEAT ASSEMBLY

43. Attach the Large Backrest (41) to the Front		43
Upright (42) with two 1/4” x 2 1/2” Screws		43
Upright (42) with two 1/4” x 2 1/2” Screws
(43) and two 1/4” Washers (10).	The
Backrest must be oriented as shown.
				41
		43	10	42
				42
				Thick End
44. Press a 1 1/2” Square Inner Cap (32) into the		44
Front Seat Frame (36).		44
Front Seat Frame (36).
Insert the 1/4” x 2 1/4” Carriage Bolt (38) into
the center hole in a Seat Plate (37). Attach
the Seat Plate to the Seat (13) with two 1/4” x
3/4” Screws (18).
Insert the 1/4” x 2 1/4” Carriage Bolt (38) into				13
the indicated hole in the Front Seat Frame
(36). Tighten a 1/4” Nylon Locknut (2) with a
1/4” Washer (10) onto the Carriage Bolt.
Attach the other end of the Seat (13) to the				38
Front Seat Frame (36) with a 1/4” Washer			37
(10) and the 1/4” x 2 1/4” Screw (82).			37	32
(10) and the 1/4” x 2 1/4” Screw (82).				32
				18
			10	36
				36
			82	2
				2

Page 19

Image 19

Weider WESY97300 Seat Assembly, Upright 42 with two 1/4 x 2 1/2 Screws Two 1/4 Washers, Thick End, 1/4 x 2 1/4 Screw

Contents

Serial Number Decal QUESTIONS?Patent Pending Model No. WESY97300 Serial No Limited Warranty Table of Contents Ing down Important Precautions Before YOU Begin Using the Weider PRO 9730 Home Gym System Before beginning assembly, be sure that AssemblyFrame Assembly Following Tools not Included are Required for Assembly Do not tighten Nylon Locknuts yet Must be at Slide eight Weights 25 onto the WeightThis side Lubricate Pins Same side That the indicated holes are on the side Shown Frame Assembly ARM Assembly Welded Brackets Lubricate Axle 2 Bolt 7 and a 3/8 Nylon LocknutTap two 1 Retainers 69 and a 1 Round Attach the Left Arm 47 in the same manner Locate the High Cable Be sure that Cable AssemblyPulley Bracket must Frame 55 with a 3/8 x 1 3/4 Bolt 87 and a 3/8 Nylon Locknut AssemblyRoute the High Cable 23 around one 8 Nylon Locknut Locknut Locate the Press CableTwo 5/16 Nylon Jam Nuts Cable to pivot Press Frame Locate the Low CableSlide the Low Cable into place under the 3 1/2 Low Pulley Press Frame 17 and that the Cable is Pulley as shown Be sure that Cable Trap is turned to hold the CableWrap the Low Cable 86 around a V-Pulley Locate the Rear Cable 95. Attach the Rear Onto the Bolt. Do not overtighten the Nylon Locknut Cable must be routed from the direc- tion shown 4 Bolt 87 and a 3/8 Nylon Locknut Seat Plate to a Seat 13 with two 1/4 x 3/4 Screws Two 1/4 WashersUpright with a 5/16 x 2 3/4 Carriage Bolt A Seat Knob Tighten a 1/4 Nylon Locknut 2 with a Seat AssemblyUpright 42 with two 1/4 x 2 1/2 Screws Two 1/4 Washers Thick End With the Bolt and a 5/16 Nylon Locknut Press a 1 1/2 Square Inner Cap 32 into the Leg LeverLubricate-33 Pin Misc Cable with two Cable Clips AdjustmentChanging the Weight Setting Attaching the LAT BAR or Nylon Strap to High Pulley Station With the 5/16 x 2 3/4 Carriage Bolt 14 and the Seat Knob Attaching the LEG Lever to the LOW Pulley StationAttach one end of the Chain 52 to the Low Cable Attaching and Removing the Seats Lbs Weight Resistance Chart Woven cable, the type of cable used on the home TROUBLE-SHOOTING and MaintenanceFrom the Weight Tube not shown or remove Tightening the Cables Weight Stack Cable DiagramsRear Base Press Cable Rear Upright High Cable Ordering Replacement Parts WESY97300 R1097A Check to see if it has been pre-assembled 16 x 2 3/4 Carriage Bolt Retainer Round Inner Cap Remove this Part LIST/EXPLODED Drawing from the Manual Description Part LIST-Model No. WESY97300 Exploded

SEAT ASSEMBLY

Upright (42) with two 1/4” x 2 1/2” Screws

(43) and two 1/4” Washers (10).

Thick End

(36). Tighten a 1/4” Nylon Locknut (2) with a

(10) and the 1/4” x 2 1/4” Screw (82).