16 x 2 3/4 Carriage Bolt | Weider WESY97300 manual

1/4" Nylon Locknut (2)–5

1/4" x 2 1/4" Carriage Bolt (38)–1

5/16" Nylon Jam Nut (84)–2

5/16" Nylon Locknut (3)–24

1/4" x 2 1/2" Screw (43)–5

3/8" Nylon Locknut (21)–22

1/4" x 2 1/2" Carriage Bolt (91)–1

1/4" Washer (10)–11

1/4" x 2 1/4" Screw (82)–1

5/16" Washer (8)–11

5/16" x 2 3/4" Bolt (11)–6

3/8" Washer (9)–7

5/16" x 2 1/2" Carriage Bolt (1)–4

1/4" x 3/4" Screw (18)–4

#8 x 1/2" Tap Screw (89)–1	5/16" x 2 3/4" Carriage Bolt (14)–2

5/16" x 5" Bolt (68)–1

5/16" x 6" Bolt (60)–2

Page 30

Image 30

Weider WESY97300 user manual 16 x 2 3/4 Carriage Bolt

Contents

Model No. WESY97300 Serial No QUESTIONS?Patent Pending Serial Number Decal Table of Contents Limited Warranty Important Precautions Ing down Using the Weider PRO 9730 Home Gym System Before YOU Begin Following Tools not Included are Required for Assembly AssemblyFrame Assembly Before beginning assembly, be sure that Do not tighten Nylon Locknuts yet Same side Slide eight Weights 25 onto the WeightThis side Lubricate Pins Must be at Frame Assembly ARM Assembly That the indicated holes are on the side Shown Attach the Left Arm 47 in the same manner 2 Bolt 7 and a 3/8 Nylon LocknutTap two 1 Retainers 69 and a 1 Round Welded Brackets Lubricate Axle Locate the High Cable Cable Assembly Be sure thatPulley Bracket must 8 Nylon Locknut AssemblyRoute the High Cable 23 around one Frame 55 with a 3/8 x 1 3/4 Bolt 87 and a 3/8 Nylon Locknut Cable to pivot Locate the Press CableTwo 5/16 Nylon Jam Nuts Locknut Press Frame 17 and that the Cable is Locate the Low CableSlide the Low Cable into place under the 3 1/2 Low Pulley Press Frame Be sure that Cable Trap is turned to hold the Cable Pulley as shownWrap the Low Cable 86 around a V-Pulley Onto the Bolt. Do not overtighten the Nylon Locknut Locate the Rear Cable 95. Attach the Rear 4 Bolt 87 and a 3/8 Nylon Locknut Cable must be routed from the direc- tion shown Two 1/4 Washers Seat Plate to a Seat 13 with two 1/4 x 3/4 ScrewsUpright with a 5/16 x 2 3/4 Carriage Bolt A Seat Knob Thick End Seat AssemblyUpright 42 with two 1/4 x 2 1/2 Screws Two 1/4 Washers Tighten a 1/4 Nylon Locknut 2 with a Press a 1 1/2 Square Inner Cap 32 into the Leg Lever With the Bolt and a 5/16 Nylon LocknutLubricate-33 Pin Misc Attaching the LAT BAR or Nylon Strap to High Pulley Station AdjustmentChanging the Weight Setting Cable with two Cable Clips Attaching and Removing the Seats Attaching the LEG Lever to the LOW Pulley StationAttach one end of the Chain 52 to the Low Cable With the 5/16 x 2 3/4 Carriage Bolt 14 and the Seat Knob Weight Resistance Chart Lbs Tightening the Cables TROUBLE-SHOOTING and MaintenanceFrom the Weight Tube not shown or remove Woven cable, the type of cable used on the home Cable Diagrams Weight StackRear Base High Cable Press Cable Rear Upright Ordering Replacement Parts Check to see if it has been pre-assembled WESY97300 R1097A 16 x 2 3/4 Carriage Bolt Retainer Round Inner Cap Remove this Part LIST/EXPLODED Drawing from the Manual Part LIST-Model No. WESY97300 Description Exploded

5/16" x 2 3/4" Carriage Bolt (14)–2