Manuals / Weider / Fitness & Sports / Home Gym

Weider user manual Check to see if it has been pre-assembled, WESY97300 R1097A

Models: WESY97300

1 35

Download 35 pages 55.45 Kb

Page 29

Image 29

REMOVE THIS PART IDENTIFICATION

CHART FROM THE MANUAL

This chart is provided to help you identify the small parts used in assembly.		Important: Some parts
may have been pre-assembled for shipping purposes. If you cannot find a part in the parts bags,
check to see if it has been pre-assembled.	The number in parenthesis	below each part refers to the

key number of the part. The second number refers to the quantity needed for assembly.

Please Note: The assembly is divided into four stages: 1) frame assembly, 2) press, squat, and butterfly arm assembly, 3) cable and pulley assembly, and 4) seat and backrest assembly. The hardware for each stage is packaged separately. Wait until you begin each assembly stage to open that parts bag.

WESY97300 R1097A

Page 29

Image 29

Weider user manual Check to see if it has been pre-assembled, WESY97300 R1097A

Contents

Patent Pending QUESTIONS?Model No. WESY97300 Serial No Serial Number DecalLimited Warranty Table of ContentsIng down Important PrecautionsBefore YOU Begin Using the Weider PRO 9730 Home Gym SystemFrame Assembly AssemblyFollowing Tools not Included are Required for Assembly Before beginning assembly, be sure thatDo not tighten Nylon Locknuts yet This side Lubricate Pins Slide eight Weights 25 onto the WeightSame side Must be atThat the indicated holes are on the side Shown Frame Assembly ARM AssemblyTap two 1 Retainers 69 and a 1 Round 2 Bolt 7 and a 3/8 Nylon LocknutAttach the Left Arm 47 in the same manner Welded Brackets Lubricate AxleLocate the High Cable Pulley Bracket must Cable AssemblyBe sure that Route the High Cable 23 around one Assembly8 Nylon Locknut Frame 55 with a 3/8 x 1 3/4 Bolt 87 and a 3/8 Nylon LocknutTwo 5/16 Nylon Jam Nuts Locate the Press CableCable to pivot LocknutSlide the Low Cable into place under the 3 1/2 Low Pulley Locate the Low CablePress Frame 17 and that the Cable is Press FrameWrap the Low Cable 86 around a V-Pulley Be sure that Cable Trap is turned to hold the CablePulley as shown Locate the Rear Cable 95. Attach the Rear Onto the Bolt. Do not overtighten the Nylon LocknutCable must be routed from the direc- tion shown 4 Bolt 87 and a 3/8 Nylon LocknutUpright with a 5/16 x 2 3/4 Carriage Bolt A Seat Knob Two 1/4 WashersSeat Plate to a Seat 13 with two 1/4 x 3/4 Screws Upright 42 with two 1/4 x 2 1/2 Screws Two 1/4 Washers Seat AssemblyThick End Tighten a 1/4 Nylon Locknut 2 with aLubricate-33 Pin Press a 1 1/2 Square Inner Cap 32 into the Leg LeverWith the Bolt and a 5/16 Nylon Locknut Misc Changing the Weight Setting AdjustmentAttaching the LAT BAR or Nylon Strap to High Pulley Station Cable with two Cable ClipsAttach one end of the Chain 52 to the Low Cable Attaching the LEG Lever to the LOW Pulley StationAttaching and Removing the Seats With the 5/16 x 2 3/4 Carriage Bolt 14 and the Seat KnobLbs Weight Resistance ChartFrom the Weight Tube not shown or remove TROUBLE-SHOOTING and MaintenanceTightening the Cables Woven cable, the type of cable used on the homeRear Base Cable DiagramsWeight Stack Press Cable Rear Upright High CableOrdering Replacement Parts WESY97300 R1097A Check to see if it has been pre-assembled16 x 2 3/4 Carriage Bolt Retainer Round Inner Cap Remove this Part LIST/EXPLODED Drawing from the Manual Description Part LIST-Model No. WESY97300Exploded

REMOVE THIS PART IDENTIFICATION

CHART FROM THE MANUAL

check to see if it has been pre-assembled.

WESY97300 R1097A