Misc, Pro | Weider WESY97300 instruction

48.Remove the backing from the PRO 9730 decal and apply it to the home gym system as shown.

MISC

PRO 9730

49.Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in ADJUSTMENT, beginning on page 22 of this manual.

Before using the home gym system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem.

IMPORTANT: If the cables are not properly installed, they may be damaged when heavy weight

is used. See the CABLE DIAGRAMS on page 26 and 27 of this manual for proper cable routing. If there is any slack in the cables, you will need to remove it by tightening the cables. See TROUBLE-SHOOTING AND MAINTENANCE on page 25.

Page 21

Image 21

Contents

Patent Pending QUESTIONS?Model No. WESY97300 Serial No Serial Number Decal Limited Warranty Table of Contents Ing down Important Precautions Before YOU Begin Using the Weider PRO 9730 Home Gym System Frame Assembly AssemblyFollowing Tools not Included are Required for Assembly Before beginning assembly, be sure that Do not tighten Nylon Locknuts yet This side Lubricate Pins Slide eight Weights 25 onto the WeightSame side Must be at That the indicated holes are on the side Shown Frame Assembly ARM Assembly Tap two 1 Retainers 69 and a 1 Round 2 Bolt 7 and a 3/8 Nylon LocknutAttach the Left Arm 47 in the same manner Welded Brackets Lubricate Axle Locate the High Cable Cable Assembly Be sure thatPulley Bracket must Route the High Cable 23 around one Assembly8 Nylon Locknut Frame 55 with a 3/8 x 1 3/4 Bolt 87 and a 3/8 Nylon Locknut Two 5/16 Nylon Jam Nuts Locate the Press CableCable to pivot Locknut Slide the Low Cable into place under the 3 1/2 Low Pulley Locate the Low CablePress Frame 17 and that the Cable is Press Frame Be sure that Cable Trap is turned to hold the Cable Pulley as shownWrap the Low Cable 86 around a V-Pulley Locate the Rear Cable 95. Attach the Rear Onto the Bolt. Do not overtighten the Nylon Locknut Cable must be routed from the direc- tion shown 4 Bolt 87 and a 3/8 Nylon Locknut Two 1/4 Washers Seat Plate to a Seat 13 with two 1/4 x 3/4 ScrewsUpright with a 5/16 x 2 3/4 Carriage Bolt A Seat Knob Upright 42 with two 1/4 x 2 1/2 Screws Two 1/4 Washers Seat AssemblyThick End Tighten a 1/4 Nylon Locknut 2 with a Press a 1 1/2 Square Inner Cap 32 into the Leg Lever With the Bolt and a 5/16 Nylon LocknutLubricate-33 Pin Misc Changing the Weight Setting AdjustmentAttaching the LAT BAR or Nylon Strap to High Pulley Station Cable with two Cable Clips Attach one end of the Chain 52 to the Low Cable Attaching the LEG Lever to the LOW Pulley StationAttaching and Removing the Seats With the 5/16 x 2 3/4 Carriage Bolt 14 and the Seat Knob Lbs Weight Resistance Chart From the Weight Tube not shown or remove TROUBLE-SHOOTING and MaintenanceTightening the Cables Woven cable, the type of cable used on the home Cable Diagrams Weight StackRear Base Press Cable Rear Upright High Cable Ordering Replacement Parts WESY97300 R1097A Check to see if it has been pre-assembled 16 x 2 3/4 Carriage Bolt Retainer Round Inner Cap Remove this Part LIST/EXPLODED Drawing from the Manual Description Part LIST-Model No. WESY97300 Exploded

Weider WESY97300 user manual Misc, Pro

Models: WESY97300

MISC

PRO 9730