Locate the Rear Cable 95. Attach the Rear

33. Route the Low Cable (86) over the lower

3 .1/2” Pulley (15) attached to the “I”-Plates (81). The Cable must be routed from the direction shown.

34.Slide a 5/16” Washer (8) onto a 5/16” x 3” Bolt (93). Insert the Bolt into the Front Base (4).

Slide theend of the Press Cable (88) onto the Bolt. Fully tighten a 5/16” Nylon Locknut (3)

onto the Bolt. Do not overtighten the Nylon

Locknut.

ASSEMBLY	35. Attach the Small “U”-Bracket (67) to the indi-
	35. Attach the Small “U”-Bracket (67) to the indi-
	cated Weight Tube (63) a the 5/16” x 1 3/4”
CABLE	Bolt (72) and a 5/16” Nylon Locknut (3).
CABLE

36. Locate the Rear Cable (95). Attach the Rear

Cable to the Rear Base (51) with the 3/8” x 3/4” Bolt (24) and a 3/8” Nylon Locknut (21).

Route the Rear Cable (95) over the 3 1/2” Pulley (15) attached to the Long “U”-Bracket (57).

33
81
15
86
34
	8	93
	8
86
3		4
35
		3
72		67
72		63
		63
36
	57
	15	95
		95
	24
51		21
		21

Page 16

Image 16

Weider WESY97300 user manual Onto the Bolt. Do not overtighten the Nylon Locknut, Locate the Rear Cable 95. Attach the Rear

Contents

QUESTIONS? Patent PendingModel No. WESY97300 Serial No Serial Number Decal Table of Contents Limited Warranty Important Precautions Ing down Using the Weider PRO 9730 Home Gym System Before YOU Begin Assembly Frame AssemblyFollowing Tools not Included are Required for Assembly Before beginning assembly, be sure that Do not tighten Nylon Locknuts yet Slide eight Weights 25 onto the Weight This side Lubricate PinsSame side Must be at Frame Assembly ARM Assembly That the indicated holes are on the side Shown 2 Bolt 7 and a 3/8 Nylon Locknut Tap two 1 Retainers 69 and a 1 RoundAttach the Left Arm 47 in the same manner Welded Brackets Lubricate Axle Locate the High Cable Be sure that Cable AssemblyPulley Bracket must Assembly Route the High Cable 23 around one8 Nylon Locknut Frame 55 with a 3/8 x 1 3/4 Bolt 87 and a 3/8 Nylon Locknut Locate the Press Cable Two 5/16 Nylon Jam NutsCable to pivot Locknut Locate the Low Cable Slide the Low Cable into place under the 3 1/2 Low PulleyPress Frame 17 and that the Cable is Press Frame Pulley as shown Be sure that Cable Trap is turned to hold the CableWrap the Low Cable 86 around a V-Pulley Onto the Bolt. Do not overtighten the Nylon Locknut Locate the Rear Cable 95. Attach the Rear 4 Bolt 87 and a 3/8 Nylon Locknut Cable must be routed from the direc- tion shown Seat Plate to a Seat 13 with two 1/4 x 3/4 Screws Two 1/4 WashersUpright with a 5/16 x 2 3/4 Carriage Bolt A Seat Knob Seat Assembly Upright 42 with two 1/4 x 2 1/2 Screws Two 1/4 WashersThick End Tighten a 1/4 Nylon Locknut 2 with a With the Bolt and a 5/16 Nylon Locknut Press a 1 1/2 Square Inner Cap 32 into the Leg LeverLubricate-33 Pin Misc Adjustment Changing the Weight SettingAttaching the LAT BAR or Nylon Strap to High Pulley Station Cable with two Cable Clips Attaching the LEG Lever to the LOW Pulley Station Attach one end of the Chain 52 to the Low CableAttaching and Removing the Seats With the 5/16 x 2 3/4 Carriage Bolt 14 and the Seat Knob Weight Resistance Chart Lbs TROUBLE-SHOOTING and Maintenance From the Weight Tube not shown or removeTightening the Cables Woven cable, the type of cable used on the home Weight Stack Cable DiagramsRear Base High Cable Press Cable Rear Upright Ordering Replacement Parts Check to see if it has been pre-assembled WESY97300 R1097A 16 x 2 3/4 Carriage Bolt Retainer Round Inner Cap Remove this Part LIST/EXPLODED Drawing from the Manual Part LIST-Model No. WESY97300 Description Exploded

onto the Bolt. Do not overtighten the Nylon

Locknut.

ASSEMBLY

CABLE

36. Locate the Rear Cable (95). Attach the Rear