FRAME ASSEMBLY
ARM ASSEMBLY
7. Press a 2” Square Inner Cap (27) into each | 7 |
|
|
| |
end of the Top Frame (55). Press a 1 3/4” |
|
|
| ||
|
|
|
| ||
Square Inner Cap (44) into each end of the |
|
|
|
| |
crossbar on the Top Frame. Press two 1” |
|
|
|
| |
Round Inner Caps (49) into the top of the |
|
|
|
| |
crossbar. |
|
|
|
|
|
Attach the Top Frame (55) to the Front Upright |
| 11 | 11 |
| |
|
|
| |||
|
|
|
| ||
(42) and the Rear Upright (56) with four 5/16” |
|
|
|
| |
x 2 3/4” Bolts (11), four 5/16” Washers (8), |
|
|
| 27 | |
and four 5/16” Nylon Locknuts (3). | 27 | 8 | 8 | 44 | |
|
|
|
| 49 | |
|
|
|
|
| 27 |
|
| 55 |
|
|
|
|
| 27 |
|
| Crossbar |
|
|
| 44 |
|
|
|
| 3 |
|
|
|
|
|
|
| 3 |
|
|
|
| 56 |
|
|
|
|
|
|
| 42 |
8. Attach the each set of the Weight Guides (62) | 8 |
|
|
| |
to the Top Frame (55) with a 5/16” x 6” Bolt |
|
|
| ||
|
|
| 61 | ||
(60), two 1/2” x 3/4” Spacers (61), and a 5/16” |
|
| 3 | ||
|
|
| |||
Nylon Locknut (3). |
| 61 |
| ||
|
| 62 | |||
|
|
|
| ||
|
|
| 55 |
| |
Tighten all Nylon Locknuts used in steps 3 |
|
| 60 | ||
through 8. |
|
|
|
|
|
|
| 3 |
|
|
|
|
|
| 60 |
|
|
|
|
| 62 |
|
|
9. Press a 1” x 7/8” Plastic Bushing (75) onto | 9 |
|
|
| |
each welded spacer on the Press Frame (17). |
| Holes must be | |||
|
| ||||
Slide the Press Frame into place on the Front |
|
| |||
|
|
| on this side | ||
Base (4). | Note: This will be a tight fit. The |
|
|
|
|
Plastic Bushings should fit onto each end |
|
|
| Lubricate | |
of the indicated tube in the Base. Be sure |
| 17 |
| ||
that the indicated holes are on the side |
|
| 59 | ||
|
|
| |||
shown. |
|
|
|
|
|
Lubricate the 3/8” x 8” Bolt (59). Attach the |
|
|
| Welded | |
|
|
| Spacers | ||
Press Frame (17) to the Front Base (4) with |
| 21 |
| ||
|
|
| |||
the Bolt and a 3/8” Nylon Locknut (21). |
|
|
| ||
|
| 75 | |||
|
|
| 4 | ||
|
| Tube |
|
| |
|
|
|
|
| |
|
| 8 |
|
|
|
