Manual Diagnostic Mode | Whirlpool GVW9959K-0 specs

Manual Diagnostic Mode

Options

Status

So ak	Wa sh	Rinse
	Wa sh		Extra
				Sp in &

			Rinse		Cycle
			Rinse	Fluff	Cycle
					Complete

Extra Heavy	Hot	Cold
Heavy	Warm	Warm	Assured
Normal	Warm	Cold	Water
Light	Cold	Cold	Tem p	Louder	Estimated Time
Refresh	Cold	Cold		Softer	Remaining
				Softer
				Off
				Off

Start

Stop

Canc el

SOAK		CYCLE
		CYCLE
	Fig. 4-2	SIGNAL
	Fig. 4-2

The manual diagnostic mode will enable activation of specific machine functions without having to run a cycle. Each function test will time out in three (3) minutes. To enter the manual diagnostic mode:

1.Press:SOAK - CYCLE SIGNAL - SOAK - CYCLE SIGNAL

within five (5) seconds while the machine is in Standby Mode. The 7-segment LED will display “dt”.

2.Press the WATER TEMP keypad. The 7-segment display show “00”. See Nutate and Recircul ate Test on next page.

In this mode the Peekaboo function is disabled. Opening the lid will stop the drive motor and all functions.

Running Nutate or Spin

3.Continue with steps in Nutate and Recirculate Test to step 12. At that point, the motor can be started in Nutate by pressing the START keypad. Nutate speeds are selectable by pressing the Cycle keypads as shown in the table below. Pressing the START keypad a second time will pause the motor. Speeds can be changed without pausing the motor. If the lid is opened during this test, it must be closed and the START keypad must be pressed again to restart the motor.

The motor can be run in Spin by pressing the RINSE & SPIN keypad. The RINSE & SPIN LED will light up. Then press START. The motor does not need to be paused to change from nutate to spin. When performing the spin speed test, the Wash LED will flash while the unit is ramping up to speed.

CYCLE	NUTATE	SPIN
	SPEED	SPEED

Whitest Whites	150	60

Heavy Duty	225	250

Normal	250	300
Jeans/Darks	275	400
Bulky Items	300	500

Quick Wash	300	600

Delicate Casual	300	800

Wool	300	800

49

Image 53

Whirlpool GVW9959K-0 manual Manual Diagnostic Mode, Running Nutate or Spin, PressSOAK Cycle Signal Soak Cycle Signal

Contents

Page Introduction Table of Contents Model Number Designator Model Number G V W 9 9 5 9 K Q SafetyMODEL/SERIAL Number Plate Serial Number Designator Considerations InstallationSection ONE For a permanently connected washer Tools needed Parts Supplied DrainSystem ConnectingtheDrainHose InstallationChecklist Use&CareInformation Section TWO Theory of OperationNutation Control Panel Soil Level Operational Cycle Default Wash and SpinOption Descriptions Assured Water Temp Water TempATC Thresholds Whitest Whites Additional Options End of Cycle Signal Drive Motor Machine ControllerMotor Controller Leveler Peekaboo Mode Universal Joint Shield Capacitor Interlock SwitchesDrive System OPR FLD Pressure SwitchesLOG Valve Assembly Water Pump/Pump Motor Recirculation and DrainOuter Tub Recirculation Changing Cycles and Options DrainChanging Cycles after pressing Start Changing Options after pressing Start Operational Cycle Notes Drive Motor Notes Pump Drive Description Water Description Water Pump Drive Duration Description Water Pump Drive Pump Drive Description Action Speed Pump Drive Description Delicate/Casual SPIN+RECIRC+FILL Wash Detergent PS Controlled Recirc Spin Garments are labelled Hand Wash because Handwash Extend Spin Cycle Soak CycleExtra Rinse To use or change Rinse & Spin settings When to use Rinse & SpinSuds Lock Detection/Cleanout Rinse & Spin Special TOOLS/PARTS Required for Service Component AccessSection Three Component Location Electrostatic Discharge ESD Sensitive Electronics Accessing Components in the Console Removing Console Components Removing the ConsoleRemoving the Machine Control Board Removing the Motor Control Board Removing the Log Valve Assembly Removing the Pressure Switches Raising the Washer Top to the Service Position Accessing Components Beneath the Washer TOP Ket. Fig Removing Components in the Tub 18b Reassembling Tub Components Tab Removing the Front Cabinet Panel Accessing Components Beneath the TUBComponents Accessible with Front Cabinet Panel Removed Removing the Drive Motor Servicing Components from the Bottom of the WasherRemoving the Thrust Plate Motor mounting bracket to the motor plate 32 shows all the components of the thrust plate assembly Removing the Brake Assembly/Nutate Shaft Replacing the Outer Tub Removing the Pump and Pump MotorReplacing the Capacitor Section Four Troubleshooting and DiagnosisTroubleshooting Chart Won’t Nutate OverfillsWon’t Spin Motor Overheats Won’t Drain TemperatureWasher Vibrating Incorrect Water Processor Reset Power FailureError Load is Wrinkled Long Drain Lid Switch ErrorAverage Current Limit Automatic Service Diagnostics Mode Self Diagnostic RoutinesOpen Lid Suds Lock Running Nutate or Spin Manual Diagnostic ModePressSOAK Cycle Signal Soak Cycle Signal Nutate and Recirculate Test Pump Drain/Recirculation Water Inlet and Dispenser VALVE, Operating PS Test If none of the LEDs light up Console Switches and Indicators TestIf a particular group of LEDs does not light up If a single LED does not light up Checking Touchpad Functioning KEY Switch Matrix Checking Drive and Pump Motor Continuity Sales Demo Mode Water Inlet and Dispenser Solenoid Test Troubleshooting Tests120VAC Electrical Supply Motor Controller Motor and Motor Control System TestMachine Control Relay If the fill valves are working properly Automatic Temperature Control TestDrive Motor and Wiring Harness Drain/Recirculation Test Operating and Over Fill Pressure Switch TestPage Page Section Five Wiring DiagramTech Tips Warranty Information Component Resistance Chart United States Rprt