Manuals / Brands / Laundry Appliance / Washer / Whirlpool / Laundry Appliance / Washer

Whirlpool GVW9959K-0 WATER INLET AND DISPENSER VALVE, OPERATING PS TEST

1 68

Download 68 pages, 1.86 Mb

51

WATER INLET AND DISPENSER VALVE, OPERATING PS TEST

If Operating Pressure S witch trips at any time , all water valves shoul d turn off. Press EXTR A RINSE to start

draining after key pres s #5 to start draining. Press EXTRA RINSE again to turn off the pump .

PRESS TOUCHPAD DISPLAY CONTROL ACTION

1 SOAK Key Dance key press #1

2 CYCLE SIGNAL Key Dance key press #2

3 SOAK Key Dance key press #3

4CYCLE SIGNAL Key Dance key press #4

Presses #1 - #4 must be completed in 5 seconds or the key

dance is not valid.

5WATER TEMP Key press #5, “00” on t he display

6WATER TEMP Cold Water Inlet Valve and Fabric Softener dis penser valve

on. Cold/Cold and Norm al (above SOIL LEVEL) LED s will

turn on.

7 SOIL LEVEL Normal LED will turn off and Heavy LED will turn on. Fabric

softener valve will shut off and Fres h w at er val v e wi ll tur n on .

8 SOIL LEVEL Heavy LED will turn off and Refresh will turn on. Fresh water

valve will turn off and Detergent dis p ens er valve will turn on.

9 SOIL LEVEL Refresh LED will turn off and Light LED w ill tur n on .

Detergent valve will turn off and Bl eac h val ve will turn on.

10 SOIL LEVEL This key press turns off the Bleach and t ur ns on t h e Fabr ic

Softener.

11 WATER TEMP C old/C old LED turns off and Hot/Cold LED tur ns on. Cold

inlet valve turns off and Hot inlet val ve tur ns on.

12 WATER TEMP B oth hot and cold inlet val ves turn on.

13 WATER TEMP All valves turn off.

14 STOP/CANCEL All LEDs off Cancel all diagnostics, g o back to Off mode.

Contents

Main INTRODUCTION GOALS AND OBJECTIVES TABLE OF CONTENTS MODEL/SERIAL NUMBER PLATE SERIAL NUMBER DESIGNATOR C L 36 50001 Model/Serial MODEL NUMBER DESIGNATOR SAFETY ! WARNING GW 9 V95 9KQ0 SECTION ONE INSTALLATION CONSIDERATIONS INSTALLATION INSTRUCTIONS Electrical Requirements ! WARNING 2 Tools needed and Parts Supplied Fig. 1-3 Fig. 1-4 Selecting a Location Fig. 1-2 3 Alternate Parts You May Need Fig. 1-6 Preparation ! WARNING Installing feet Connecting the Inlet Hose Fig. 1-8 Fig. 1-9 Fig. 1-10 Connecting the Drain Hose Leveling the Washer Fig. 1-14 Installation Checklist Securing the Drain Hose Fig. 1-11 Use & Care Information SECTION TWO THEORY OF OPERATION CYCLE DESCRIPTIONS CONTROL PANEL NUTATION OPTION DESCRIPTIONS Soil Level CYCLE SOIL LEVEL EX HEAVY HEAVY NORMAL LIGHT REFRESH OPERATIONAL CYCLE DEFAUL T W ASH AND SPIN Water Temp SELECTED CYCLE DEFAULT WATER TEMP Assured Water Temp ATC Thresholds End of Cycle Signal THERMISTOR RESISTANCE CHART THERMISTOR RESISTANCE Additional Options DESCRIPTIONS OPTIONS Soak Extra Rinse Extend Spin MACHINE CONTROLLER MOTOR CONTROLLER DRIVE MOTOR NUTATION Peekaboo Mode LEVELER UNIVERSAL JOINT INTERLOCK SWITCHES Shield Capacitor DRIVE SYSTEM PRESSURE SWITCHES OPR FLD LOG VALVE ASSEMBLY RECIRCULATION AND DRAIN Water Pump/Pump Motor Outer Tub Recirculation Changing Cycles and Options Drain OPERATIONAL CYCLE NOTES Page 20 21 22 23 24 25 26 27 28 Page 30 Suds Lock Detection/Cleanout 31 SECTION THREE COMPONENT ACCESS Seal Kit, Part #285842 COMPONENT LOCATION SPECIAL TOOLS/PARTS REQUIRED FOR SERVICE Putty Knife T-40 Torx Spanner Wrench Volt-Ohm Meter ! WARNING ! IMPORTANT Electrostatic Discharge (ESD) Sensitive Electronics Removing the Console Removing Console Components ! WARNING Removing the Machine Control Board Removing the Motor Control Board FLD OPR Removing the Log Valve Assembly ACCESSING COMPONENTS BENEATH THE WASHER TOP Raising the Washer Top to the Service Position ! WARNING Removing Components in the Tub Reassembling Tub Components Page ACCESSING COMPONENTS BENEATH THE TUB Removing the Front Cabinet Panel Components Accessible with Front Cabinet Panel Removed Servicing Components from the Bottom of the Washer Removing the Drive Motor Removing the Thrust Plate Removing the Brake Assembly/Nutate Shaft Removing the Pump and Pump Motor Replacing the Capacitor Replacing the Outer Tub SECTION FOUR TROUBLESHOOTING AND DIAGNOSIS TROUBLESHOOTING CHART Wont Power Up AM Radio or TV Interference Wont Start Cycle Overfills Wont Spin Tripping GFI Wont Nutate Motor Overheats Wont Drain Washer Vibrating Display Flashing Incorrect Water Temperature Wont Recirculate Rinse Water Long Fill L F Load is Wrinkled Load is Tangled/ Twisted Clogged Dispensers/ Bleach Leaking/ Bleach on Wrong Loads Power Failure P F Flood Condition F L C E C L S A C I SELF DIAGNOSTIC ROUTINES Automatic Service Diagnostics Mode Suds Lock S L Open Lid Manual Diagnostic Mode Running Nutate or Spin 50 NUTATE AND RECIRCULATE TEST Pump Drain/Recirculation WATER INLET AND DISPENSER VALVE, OPERATING PS TEST Console Switches and Indicators Test If none of the LEDs light up: If a particular group of LEDs does not light up: If a single LED does not light up: If no beep sound is heard: KEY SWITCH MATRIX Checking Touchpad Functioning: RESISTANCE CHART CHECKING DRIVE AND PUMP MOTOR CONTINUITY Sales Demo Mode TROUBLESHOOTING TESTS 120VAC Electrical Supply Water Inlet and Dispenser Solenoid Test Motor and Motor Control System Test Machine Control Relay Motor Controller Automatic Temperature Control Test Drive Motor and Wiring Harness Operating and Over Fill Pressure Switch Test Drain/Recirculation Test Page Page Page RESISTANCE CHART COMPONENT RESISTANCE CHART WARRANTY INFORMATION ONE-YEAR FULL WARRANTY FIVE-YEAR LIMITED WARRANTY TEN-YEAR LIMITED WARRANTY